Search:
Results: 88169
Make Model Symptom Problem Solution By
SHARP C-2041C
Screen with dark half up and down Signs of a capacitor with little capacitance in the vertical part Tests with the capacitor in the vertical part finding the capacitor 1000 by 35 volts (c507 on the chassis) with a capacitance of 128 instead of 1000 replaced and it was ok Alarsatec
VISIONTEC SMART
Everything turns on normally but tsound is no image and the relay does not activate Q1=Bqqah Replace for b772 or bd 139 adriano zimmer
CENTURY RTS 1900
No sound and no video with black screen First the device turned on but the relay did not arm, it was tr q1 and diode d10 then the screen remained dark After changing all the capacitors, I found the qv20 transistor with a leak on all the pins, I replaced it and it was ok. GSAELETRONICA GRANJA CALIFORNIA
CENTURY PR2010
I'm sound L1 coil with problems After changing and adjusting the duct ok. George Pontes
SONY KDL-40EX605
Power supply beating relay 12 volts at the foot of the relay ry 601 change the diode I put a 12 volt diode and it was beautiful Israel de Oliveira
TOSHIBA LC3242
Doesn't start 6 22mf capacitors, 1 100mf and 2 150mf open and altered Just replace and run to the crowd Wenceslau
H-BUSTER HBTV-3203HD
Turning off the lamps after some time Defect in lamps or inverter transformers Remove r720 from the circuit and this disables protection Infotron-ltda Marcos Paulo
SAMSUNG CL21K40MQ
League has sound, but no image. If you enlarge the screen, retrace lines appear. Dz 201de 9v. on the main board near the rgb socket Replace for the same or approximate value. exe: 8.2v. never greater than 9v. Gleydson Palheta
TOSHIBA 2086
Reduced frame burning the horizontal 7n8 wide capacitor HP ELETRONICA
SONY GT111Z
Standbay Front plate sweet moth Luiz
CCE HPS 2185FS
The LED blinks but the TV doesn't turn on, it lights up and goes back to standby Secondary power supply capacitor with 50v low voltage Replace the c825 47m/250v and the 33 they work together charles
CROMUS 3,8 PLUS
Device turns on and off in one second After checking all the components and not finding a defect, I analyzed the lnbf switch and found a defect in it. Replace the lnbf switch or feeder whatever you want to call it Jailson Lima
CCE HPS 2185FS
Blinking led Flyback Replace of the same charles
PHILCO PH14B
Rainbow effect normal sound looking like magnetized kinescope Cold solder on the trafo pin that goes to the vd564 Rest the traqfo on the secondary pins carlosss
AOC LE32H1461
Doesn't start Diode d9112 just change it and run to the hug tec center
TOSHIBA TV2916LMS
LEM8
TV turns on and off quickly with vertical closed R311 open (in my case the TV had already come from another technician, the resistor was no longer in place) I put one in and the TV is new (obs. resistor 3k-smd) Antonio Carlos(Eletrônica Renascer
AIWA CX-S559LH
Does not turn on - only standby LED is on Q067 with leak Replace do transistor smd code lf Guimaraes
CCE TV2118USP/AV
Lack of width, reduced frame. Chap. 100uf/160v elco broken, it is the filter on the +b line jr_TEC
CCE TV2118USP/AV
Black stripe on the right side of the screen. Chap. of damaged disc ceramic in position c417 (330pf/2kv) jr_TEC
SEMP TV1450MAV
U17
No contrast, even at maximum level. Chap. of disc ceramic on the faulty screen line (1k/2kv) jr_TEC