☰

Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search:
Results: 88174
Make Model Symptom Problem Solution By
PHILIPS 32PHG4900
Doesn't start. without 12volts on the cn9101 connector. no LED on. Diode d9112 sr5100 power supply board. After changing it, the TV started working again. Eduix
CCE HPS 2005
Dead Flay black with broken clamp, shorted horizontal transit and fb of +b feed from open flay black. Replace the flay black, horizontal output and fb of the flay black power supply. Zé Mário ipueiras-ce
PHILCO TP29C21
Normal alloy appears drizzle then goes black screen. in normal av Settings Disable screen saver Zé Mário ipueiras-ce
PHILCO TP29C21
Normal alloy appears drizzle then goes black screen. in normal av Settings Disable screen saver Zé Mário ipueiras-ce
PHILCO PTH660N
Usb doesn't work, Low usb power voltage, 3.6v Inductor L700, on the main board, next to the harness connector that goes to the USB/SD board
LG 29 29FU6TL
Hitting the relay doesn't turn on, everything is ok but it doesn't turn on R 801 amended Replace of the same washington
CCE HPS2971FSG
This TV had a normal power supply, it generated mat and had no screen or sound. Checked the voltages on the fly back secondary, they were low, the +51v line only had +15v. it was the cap. polyester c409 - 560kpf/250v dry. HFSILVA
LG 21FU1RL
CW81A 		Doesn't start. The LED blinks and does not start. Low power supply voltage. 64 volts at +b and pulsing lightly. all other voltages were low below. After checking everything, it was resolved by changing the fly back vsc24-3368j. detail: even turning off the +b of the fly back did not increase the voltage. Eletrônica R-Tec
PHILCO PH43C21P
Turns on but no image When turning on I measured the voltage of vs-215 which was dropping to 10v. checking the y sus board I noticed that underneath the cn5001 connector it was toasted. vscan leak with ground Insulate or scrape the PCI wsound it is burned joansa eletronica
TOSHIBA 48L2400
Turns on the logo appears and turns off the green light on the stand is on and tsound is no function on the keyboard Burnt out bar leds Replace the bars or adapt another one to the burned out LEDs eletronica vieceli
LG CP14B85
Greenish image giving the impression of being a tube Dz502 shorted After checking the RGB tube, transistors and resistors, I found the dz502 shorted, replaced it, resolved janilson jc
SEMP 2134
SK91 		Image with black triangles in the two corners under the screen and the keys don't work Corrupted eeprom memory Replace memory 24c08wp Fofao
AOC D32W831
TV turns on and works, when it heats up, if it turns off, it no longer works, only the LED turns blue Ic-u701= g1084-33. This i.c is on the main PCI next to the largest electrolytic on the board Usually the C710 greenhouse and the C716 also replace. the i.c must be 3.3volts, if tsound is more than that, replace it. MIGUELTV
PHILIPS 29PT554
Turns on LED, has almost all voltages, but does not oscillate horizontally, has voltage on the TSH collector 7250 processor, defect caused by high voltage leakage from the fly. Replace both. Felix Tvsul
PHILCO PH21MSS
Without Audio, sometimes Audio comes on and disappears. Q602 Replace for another. JOHN GAMES
PHILIPS 29PT554
It doesn't turn on, the LED doesn't light up, tsound are no voltages. Photocoupler, use original. Attention, this model should be observed high voltage leakage of the fly, and the cause of the defects. Felix Tvsul
LG 21FU6LT
No red Q901 without voltage on the base, zd502 of 9.1v open Replace zd502 Airton
LG 21FS4RL
Works perfect but keeps turning off To do this, place a 4k7 resistor on transistor q16 between the base and emitter, and best of all, you won't mess with the TV's protection, Color tech eletrônica
PHILCO PB120N
CD and USB don't work No apparent cause, zd 114 - 6v8 shorted. Edilson_tv
PHILCO PCS2960
Cushion effect Q405 (pnp) smd. check around him Eletronica Cecé- Brumadinho MG