Aiwa Repair Tips
Search: aiwa
Results: 314
Results: 314
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| AIWA |
AD-R40U
|
Plays tape had difficulty working, crashing, reversing out of time and poor contact on the keys. | replace of cold welding belts in the connectors connecting the front plate and dry lubrication on the white gear with the motion sensor magnet, glued shaft preventing it from spinning freely. After that case resolved. | Marcio da Silva Porto | |
| AIWA |
NSX F12
|
Remember beating and protection acting and tension of 17.6 V on the Sound output | R292, R288 open and Q208 shortly. | ||
| AIWA |
AWS-TV-32-BL-01
|
no picture with sound. with led customer access 8817 | resistor R218 35V open on the ver-com also diode D209 short. client 8817 | replace R218 D 209 customer 8817 | marcos melo |
| AIWA |
AWS-TV-32-BL-02-A
|
RESET THROUGH SERVICE MODE! (FATORY MENU) USE THE ARROWS ON THE REMOTE--- PRESS power supply,INPUT,power supply + 1x <- + 1x -> + 2x <- | DO NOT replace ANY DATA ON THIS PAGE AT THE RISK OF DEMANDING THE MAIN PCI SOFTWARE. \\\"UNLESS YOU KNOW WHAT YOU ARE DOING\\\" | NAVIGATE TO THE FACTORY RESET ITEM, CHOOSE THE OPTION \\\\\\\"COM\\\\\\\" AND CONF. IN OK. THE TV WILL RESET AND CONF. INITIALS WILL HAVE TO BE REDONE. | EVANDO VIANA |
| AIWA |
AWS-TV-32-BL-02-A
|
RESET THROUGH SERVICE MODE! (FATORY MENU) | DO NOT replace ANY DATA ON THIS PAGE AT THE RISK OF DEMANDING THE MAIN PCI SOFTWARE. \\\"UNLESS YOU KNOW WHAT YOU ARE DOING\\\" | NAVIGATE TO THE FACTORY RESET ITEM, CHOOSE THE OPTION \\\"COM\\\" AND CONF. IN OK. THE TV WILL RESET AND CONF. INITIALS WILL HAVE TO BE REDONE. | EVANDO VIANA |
| AIWA |
NSX-S909
|
It turns on for a while, then turns off the front and doesn't respond to commands, but the sound continues to come out | Cristal | In my case, just resolder the crystal and it came back, but also consider replace the crystal | Sn Eletrônica |
| AIWA |
AWS-TV-55-BL-01
|
No image | Defect in the LED bars = 3 bars with 11 3V LEDs each measuring 105.8 cm long | I didn't find it in Brazil, I had to import a model equivalent to the Philco TV model PTV55G20 and PTV55G20AGS other codes LED strip lamp for Skyworth, 55suc6500, th-55hx560c, 55d11-zc62ag-04d, sw55d11-zc62ag-02, 5800-w55g22-0p00, 55d3b11cx106012 | You tube - Direto no defeito |
| AIWA |
AW42B4SM
|
Increasing the volume alone | Processor heating up abnormally, if you pour isopropyl alcohol on the processor and cool it the defect normalizes | Replacing the processor or board | LEANDRO VOSS |
| AIWA |
ZR900
|
Plays the CDs normally but sometimes it opens the tray alone if it is stopped without any function then it stays in direct shelter | Micro keys on the CD plate that is on the CD mechanics, change or clean them | ||
| AIWA |
ZR900
|
Complement no sound on the tape deck b even with two speakers and increasing the volume to maximum, the tabe a only has sound on one normal channel, the other works very quietly | Defect in ic302 (cxa1553p) just change it and go for the hug | ||
| AIWA |
ZR900
|
Carrocell doesn't spin and CD doesn't work | 33r resistor open or changed, the value must be 33r, located on the CD board and connected to the 11 or 12 v power supply | ||
| AIWA |
ZR900
|
No sound and all functions | Transistor a114 defective it releases voltage to the 60 v power supply relay if the power supply is not recognized at the beginning of the device fertilization it will not produce sound | Just replace it and that's it | |
| AIWA |
NSX-S22
S22LH |
No sound, display goes on and off | Exchanging outputs d2495 and b1626 and peak fuse pr202 | Shorted outputs due to use in low impedance and open fuse peak. | Rocha Disco & Eletrônica |
| AIWA |
CA-W37
|
Very low and distorted sound in all functions. | IC701 (LA4550) Replacement | MURIEL RAMOS | |
| AIWA |
CX-NS909HR
|
I'm sound | Transistor q601(open) audio processor power supply | Eletro Zica | |
| AIWA |
AR-295
|
TV doesn't turn on--tsound is no 9.3v power supply | One of the 4k7 resistors in the resistive divider--130v--32v open | Check line voltage value 32 v,and it was, | KLEEUS |
| AIWA |
AR-295
|
Power supply does not provide 9.3v at the q802 emitter | Q 892-bc 337]16 | 10v zener from collector to emitter of q 802, clamping 9.3v at the point, | KLEEUS |
| AIWA |
NSX-S229
|
When you press the button to turn on the display turns off and does not turn on. | Check r223, r224, r249 and r250. Possibly, one of them may be open, due to some problem with the audio output. | MARCONES DE ARARIPINA-PE | |
| AIWA |
NSX-S229
|
Nothing turns on, display is off | Loosen resistor r244 and see if when plugged in, the display lights up. If it lights up, check the output transistors. | MARCONES DE ARARIPINA-PE | |
| AIWA |
CXNF 9 LH
CXNF |
When I plug it in, the PC turns on by itself and doesn't turn off. | What can it be | Renato |