Aiwa Repair Tips
Search: aiwa
Results: 314
Results: 314
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| AIWA |
NSX-S229
|
Hoarse sound and does not arm the relay | Transistor q112 open | multsom | |
| AIWA |
NSX-F969
|
It turns on the panel and turns it off, and sometimes it doesn't even light the panel. | Check q224 fet 2sk 2937 which may be faulty. | I replaced it and it stopped turning off and it worked normally, good luck to everyone, | Eronaldo (erontec) |
| AIWA |
NSX-F969
|
It turns on but the tuning doesn't stop, just press the tuning to stop. | Adjust coil l771 | When adjusting, the tuning was normal, good luck, (erontec). | Eronaldo (erontec) |
| AIWA |
NSX
|
Didn't care | With a screwdriver short the q115 terminal 3 between base and collector | Went back to work | gustavo |
| AIWA |
NSX F959
|
No high-pitched sound (high output) | Q102 (can be jumpered - tsound is already a place on the board next to a jumper/resistor) and q103 (can be left without) | Baguatech | |
| AIWA |
MSX-S707
|
Turns on, but then turns off! | Remove q110 smd | RODRIGO VIPO | |
| AIWA |
NSX-SZ21
|
Nao liga so standby | Q130 | Remove q130 if it turns on, just replace it or leave it without it but it is not recommended | beto2828 |
| AIWA |
NSZ21LH
|
Does not turn on, just stand by | Q130 | Just remove the q130 from the board and it will solve it | Lima |
| AIWA |
CX-NSX-SZ80
|
When plugged in, sometimes it turns on, sometimes it doesn't | Grass pt 002 | And just replace the transformer pt002 | GR eletronica |
| AIWA |
CX-S559LH
|
Does not turn on - only standby LED is on | Q067 with leak | Replace do transistor smd code lf | Guimaraes |
| AIWA |
JAX-PK1
|
Stand by light comes on and then goes off when plugged in | Burned transformer | eletronica topa tudo | |
| AIWA |
TV AR145
|
Does not light up stand by - does not turn on | Protection triggered | Replace c841 (smd) without measuring - close to the power supply's 5v regulator | NV ELETRONICA |
| AIWA |
TV AR 295 RH
|
Dark square center screen | Swap memory - 24 with 8 -smd | Marco Gasparatto | |
| AIWA |
Z-R997
|
By increasing the volume, the tray opens and rotates the plate. In this case I noticed that when I reached volume 39 the tray opened, and when the analyzer worked at peak + high it also opened. | Ic 380 ba3835s spectrum analyzer | Replace or remove. | joaomvjr |
| AIWA |
CXNF9HR
|
Difficulty rotating the disc tray | Jw50 33r resistor changed .check before the belts | Replace | alvaro peralta |
| AIWA |
CXNV90HR
|
Does not activate the equalizer buttons in surround | Sale | celio pinheiro dos santos | |
| AIWA |
NSX-S303
|
When completely stopped, neither the dashboard lights up | Q 216 emitter/collector short | Replace the same | eletronica c. r. |
| AIWA |
CX-Z1200LH
|
Does not turn on, just some lights on the front panel | Transistor b108 open | maxci | |
| AIWA |
NSX-T99
|
Making noise! It sounded like snoring, all functions working (except the audio) | Around the trans.q601 tsound is a green wire glued with 1 black pinch (glue) (all components below the glue have been cold soldered) | Resoudar | Alextecnico |
| AIWA |
AR295
|
It only lights up on stand-by and doesn't start | R-816 or something close, as they are in series |