Jvc Repair Tips
Search: jvc
Results: 433
Results: 433
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| JVC |
AV25SX2EK
|
No sound | Replace s/c c613 100mfd25v | ||
| JVC |
AV25SX1EK JA
|
Int pic blanking out | Tda8350q vertical output chip (ic401). if r971 if fitted & overheating, remove it (should not be fitted in uk models) | ||
| JVC |
AV25SX1EK JA
|
Flickering/flashing pic | Fop chip replacement seems to have cured it | ||
| JVC |
AV25SX1EK JA
|
Flickering & flashing pic | Fop chip | ||
| JVC |
AV25SX1EK
|
Shuts down almost straight after sw on | Ht correct but eht high due to c1521 3,800pf 1.5kv reduced cap | ||
| JVC |
AV25SX1EK
|
No sound | Ic1952 kia7805pi 5v reg | ||
| JVC |
AV25SX1EK
|
No sound | Ic952 5v supply to dolby pcb low, check for o/c l601 n10 ccct prot. dis a mute pin 8 ic601 to restore sound. fault could be due to micro or eeprom caused by crt flashover | ||
| JVC |
AV25SX1EK
|
Int field collapse with it turning off | Dry joints around fop | ||
| JVC |
AV25SX1EK
|
Field - top cramp | Tda8350q chip faulty | ||
| JVC |
AV25SD4EK
|
Burring noise for first 20 mins | C409 100µ 65v on dolby pcb | ||
| JVC |
AV25S4EK
|
No vsm option & may come on in av mode | Before you change the ic, go into service mode (press display and vsm standard keys on the remote). go through all of the deflection settings and write down the values (don't forget to record 16:9 mode as well as 4:3) as you will need to program these into the new eeprom. when in service mode, press display and vsm standard keys again and the screen will show "system constant". this determines which facilities the set has (text, surround sound, etc.) you should also record these and program them into the new ic | ||
| JVC |
AV25S4EK
|
No sound/piv via tuner - ok via scart | 4mhz xtal in tuner can | ||
| JVC |
AV25S2EK
|
Switches on , eht rises then goes to standby | Possible corrupt eeprom, remove and set should switch on | ||
| JVC |
AV25S2EK
|
No start up after initial eht rush - reverts to st/by | Eeprom corrupt - remove eeprom to test (should then come on with snowy screen) pt no cat93c66p & prog with r/c pt no rm871e | ||
| JVC |
AV25S1EK MXII
|
Unstable pic with line jitter | Video o/p from if module has ragged sync pulses - 1µ elect cap in agc feed | ||
| JVC |
AV25S1EK MK2
|
Always comes on in st/by - sometimes at full vol | Eeprom ic104 corrupt - pt no cat93c66p | ||
| JVC |
AV25S1EK
|
Shuts down immediately after sw on | D521 by228 s/c, c468 47µ , r526 0r2 | ||
| JVC |
AV25S1EK
|
Shuts down at sw on | D521 by228 s/c, c468 47µ, r526 0r22? | ||
| JVC |
AV25S1EK
|
No line drive | R903 2.2k base bias to q902 slightly high | ||
| JVC |
AV25S1EK
|
Led goes red, then green then off at sw on - no start | R526 39r, c458 4µ7 50v & d521 by228 in e/w cct |