Lg Repair Tips

Search: lg
Results: 4915

Make	Model	Symptom	Problem	Solution	By
LG	32LV3400	Turns the STB LED on and off, nothing more	Cold welds on the processor	Reballing, to make sure that this really is it, it is possible to do a brief reflow, if it works, move on to resoldering.	Davi.sls
LG	32LH570B LJ6/LJ7	Turns on, normal, has audio. but no image, but you can see the weak image in the background, well I immediately suspected the LED bus, but it was blue and needed to be replaced. I ordered the part and put it on and nothing. the bars were good. and this TV is from an external power supply. I went to check the LED controller CI, and I found that tsound was a shorted capacitor, killing the voltage that goes to the bars, and tsound was not enough voltage to light the bars. Capacitor on pin 25 shorted. each case is different.	Changing the capacitor on pin 25 of the LED controller IC. The 32lj600b TV also uses this same circuit.	Replace it.	JC Eletrônica Cícero
LG	29LN549M	Works a little and the sound disappears or no sound	Q700	Remove the q700 and run for the hug	Gilberto Costa
LG	21FJ8RL CW-81B	TV in protection. when removing q13, it turns on without sound and with the vertical closed.	When turned on, it disarmed and returned to stand-by. removing q13 turned it on with vertical closed and without sound. resistor r620 overheating and without 5v on the pins of the corresponding components.	Removed the resistor r614, thus opening the image. reinstalled q13 and it no longer tripped. ic601 shorted.	Fernando Afonso
LG	20MT490DF	Shorted to 19v input	Short on the 19v power supply input line. cause c0921 .near the audio output.		Oscar RJ
LG	42PC5RV	No audio or intermittent audio	Capacitor c318 10uf/25v
LG	M2631D	LEDs flashing and don't light up, TV works normally	C1110 e c 1111		HP ELETRONICA
LG	50PB560B 00000	Just one image pulse then erases	C 205 smd with leakage below r 201=2.2Ω	Replace without testing * good luck!	Jhone eletronica
LG	32LN536B 32LN540B	Alloy and the image with several colored lines vertically, you can also notice a slight buzzing in the t-con.	Tcon supply voltage is low, around 9.5v. change q409		electronicssupplyparts - Gramado/RS
LG	39LB5600	Standby only, does not blink, does not respond to any command	When arming the power supply on the bench, all voltages appear normally. the processor does not heat up excessively, the main voltages of the main board are present. I suspected corrupted firmware, so I replaced the eeprom and nand memories, which solved the problem.	Replace or rewrite the ic1300 and ic102 memories	World TV - Sorocaba
LG	CM4350	After being connected for a while, the device turns off and does not turn on again (5v power supply drops to around 2.4v)	Check the 6v2 zener diode zd902 and photo coupler pc901 tsound must be 1.6v on pin 4 if it is low, replace both.		Eletronica Oliveira
LG	49LB5500 LGP474950	Piscando backlight	Q803 and/or q806 altered, LEDs burned out, screen flashing or no image (with normal sound).	The fets q803 and q806 must be tested outside the circuit, of the pf610bl type, but can be replaced by the irf8010. The only problem is to solder the pins correctly (gd and s) and fix the fets isolated from the housing.	Luisthe
LG	CP14B86A	Vertical closed	Changed r316 and r301	Replace without measuring	Tsat eletronica
LG	42LF20 EAX56856906(0)	I'm sound	L1000 diode replacement	Is close to the power supply connector	DIODO
LG	49UB8550 LJ41V	It doesn't find a wifi network and it doesn't pair the bluetooth remote control. no mac in service mode.	Resolda do microprocessor ic100 - bga cold solder		rafaelmoraes99
LG	RP-21FE85G	Horizontal output transistor q402 (tt2170) shorted, fusistor fr403 (1.2ohms 1w) open.	Cold solder on the horizontal output transformer t403, causing the horizontal frequency not to reach the horizontal output transistor, burning it.	Re-solder the transformer, install another horizontal output transistor and another fuser. I installed some tt2170, they all burned instantly and opened the fusistor too. probably counterfeit transistors. I replaced the tt2170 with a bu2520dx, it didn't burn anymore. As the bu2520dx is bigger than the tt2170, I had to make a hole in the heatsink to adapt it, but it worked perfectly.	Rgs011
LG	43UN7300	Turns on but no image	Shorted screen	Look for the lockout12 point on the right side of the vcon, count 9 tracks from right to left, isolate one track, it will be a little scratchy, but it is usable	HAHNRAHN
LG	50PG60R	Turns on, the image and normal tensions do not appear.	Processor with cold solder..	Reball	RV ELETRONICA GYN
LG	CJ98	No sound, everything else ok	X600 spacious		Adão Rosa
LG	14CB25A MC-059A	Vertical closed (I solved it, and the TV stopped after a few minutes), it wouldn't turn on with the stand by LED blinking (I solved it due to a leaky zener diode), low sound/audio (I solved it by changing capacitors). presented three defects in this sequence	Closed vertical: r301 of 15k (was changed to 22k, close to vertical); did not turn on: zd851 (6.2v) connected to the photo coupler pin.; low sound: c504 (near the varicap) and c602 (near the audio aid).	This one took work, but we did it. check and replace the aforementioned components; good luck.	Eletroboy