Search: lg
Results: 4963
Make Model Symptom Problem Solution By
LG CP14B86A
Vertical closed Changed r316 and r301 Replace without measuring Tsat eletronica
LG 42LF20
EAX56856906(0)
I'm sound L1000 diode replacement Is close to the power supply connector DIODO
LG 49UB8550
LJ41V
It doesn't find a wifi network and it doesn't pair the bluetooth remote control. no mac in service mode. Resolda do microprocessor ic100 - bga cold solder rafaelmoraes99
LG RP-21FE85G
Horizontal output transistor q402 (tt2170) shorted, fusistor fr403 (1.2ohms 1w) open. Cold solder on the horizontal output transformer t403, causing the horizontal frequency not to reach the horizontal output transistor, burning it. Re-solder the transformer, install another horizontal output transistor and another fuser. I installed some tt2170, they all burned instantly and opened the fusistor too. probably counterfeit transistors. I replaced the tt2170 with a bu2520dx, it didn't burn anymore. As the bu2520dx is bigger than the tt2170, I had to make a hole in the heatsink to adapt it, but it worked perfectly. Rgs011
LG 43UN7300
Turns on but no image Shorted screen Look for the lockout12 point on the right side of the vcon, count 9 tracks from right to left, isolate one track, it will be a little scratchy, but it is usable HAHNRAHN
LG 50PG60R
Turns on, the image and normal tensions do not appear. Processor with cold solder.. Reball RV ELETRONICA GYN
LG CJ98
No sound, everything else ok X600 spacious Adão Rosa
LG 14CB25A
MC-059A
Vertical closed (I solved it, and the TV stopped after a few minutes), it wouldn't turn on with the stand by LED blinking (I solved it due to a leaky zener diode), low sound/audio (I solved it by changing capacitors). presented three defects in this sequence Closed vertical: r301 of 15k (was changed to 22k, close to vertical); did not turn on: zd851 (6.2v) connected to the photo coupler pin.; low sound: c504 (near the varicap) and c602 (near the audio aid). This one took work, but we did it. check and replace the aforementioned components; good luck. Eletroboy
LG 42LG64FR
White screen, functions don't work Rewriting of ic 802 atmel 24c64a memory, they sell the data on the internet. Marcelo
LG 22MA22D 26MA33D 28LN500B
EAX65374603 (1.3)
Monitor does not turn on Chip responsible for the 1.2v line ic803 (mp2315) visibly burned Replace the IC, which is an mp2315, or place a linear converter or some other 1.2v voltage regulator on pin 3, which goes to the 1.2v coil. To test if this is the only problem, simply remove the burnt IC and inject 1.2v into the L801 coil, this coil goes directly to the processor, so be careful not to get the voltage wrong. a simple 1.2v 1117 sot-223 regulator will not work as the current is quite high. Darci Denzer
LG 47LG60FR
Turns on the image and turns off after 4 seconds The defect was a leak in capacitor c842 next to x1000 Just remove the c842 David Jacobina
LG CM9750
It turned on normally for a few seconds and turned off "off auto power -e good-bye" Panel tactile key Replace all the tactile keys on the panel..... problem solved neupsx4
LG 42LG30R
Turning off or not turning on intermittently. Filter capacitor c620 Replace capacitor c620 150/450v Valdenir tecvideo
LG 26LS3500
Lights up, has backlight but no image Ic 3310 has 3.3v at the input and no voltage at the output Replace IC 3310 (2.5v regulator) jose almeida tavares
LG 47LG60FR
Backlight off, flashing when starting, but does not light up. Oz9966sn oscillator on power supply board, responsible for switching the backlight circuit. Eletrônica Maurício
LG 32LM625BPSB EAX69032103
After warming up, it stops working and the rc does not work C4010 electronicssupplyparts - Gramado/RS
LG CM8340
No audio Capacitor Eletrônica lcd o melhor de Fortaleza
LG 42LS5700
TV turning on the back light with no image. C191 on a t-plate with Replace Marcus Pacheco
LG 24MT48DF
Turns on normally, after a while it locks functions. keyboard and control inoperative. 24c256a memory Changing the memory, you don't need to write anything to it. Pardal-x
LG 26LH20R ; 32LH20R
Does not turn on, does not even turn on stand-by Defect related to the primary power supply. Substituir ic500 (ice3b03653), zd501 (diodo zener 3v6), e r501 (2.2Ω). Tiago C. Neves