Search: lg
Results: 4963
Make Model Symptom Problem Solution By
LG 42LH40ED
Power on, panel access, no image Cold shoulder and bga Reflow na bga. ic100 CELSOKAYRAN
LG 37LD840
Standbay LED on, but does not turn on Defective main board, cold soldering on the bga. Reflow na bga. CELSOKAYRAN
LG 29FS4RLG
Blurred image at the bottom white stripe below opening very slowly Replace capacitor c 419 -1000mf/25v Worked with all standard screen SR LUIS CAMPOS DOS GOYTCAZES, ELETRONICA NOVA CIDADE LUZ
LG 21FU4RL
Normal image then disappeared, tsound was just a noise drizzled on the screen as if it had no synchronization R114=30k open I replaced it and the image came back normal Antonio Carlos (Eletrônica Renascer)
LG 21FU4RL
Normal image then disappeared and tsound was just a noise R114=30k open I replaced and ran to another one Antonio Carlos (Eletrônica Renascer)
LG 24MN33D
Doesn't start Diogo smd position d710 is close to the power supply connector! Vital eletrônica hawai12
LG 14SB1RB
Replacement of the fly back bsc25-n0874, with the fly back 6174v-60006h (v) (w) This replacement can be done without much problem, if you place the fly back 6174v xxxx you may experience a small deficiency in the vertical height, how can you proceed to eliminate this problem. lift the fr 301 that is connected to pin 6 of the fly back and add 04 turns to the fly back ferrite and connect these ends to pin 6 and the other to the fr 301 fuzistor, and run for the hug. Eletronica Tv color Videira sc
LG RP21FD10
TV with stand by blinking. D810 open. After changing, the LED stayed on, however, when I pressed the power key or channel + and channel - the TV did not turn on, so I analyzed the power line and found the c826 de2200ufx16v with low capacitance and it was just a matter of changing it and it started working again. normal. Another xausabde stand by led off or flashing is the control's infrared receiving photodiode open or shorted, so do as indicated and move on to another Jailson Lima
LG CM8440
Volume above 30 the audio stops for 7 seconds and returns Pfc voltage is 380v, but it only had 364v, I found the smd resistors (r917, r918, r919) changed, the 3 are 1m I replaced the 3 1m resistors, in my case, this solved the problem. C-audio eletronica (SM-AL)
LG 32LK330-SB
Tv was admitted, coming from another assistance wsound the t-con.tv board had been condemned to be completely inoperative! When opening, I disconnected the flat (pci main/t-con) and the TV turned on, tsound was sound but, of course, no image. the t-con fuse was open, when replacing it, it burned again... carrying out a quick visual inspection and continuity test on the smd capacitors, I checked the capacitor in position c31, in the dc/dc circuit (t-con ) shorted. I removed the capacitor and replaced the fuse. The TV turned on again and had no problems. I chose to leave it without the capacitor under test and it continued to work perfectly until delivery to the customer. A big hug to everyone and don't forget to post repair tips, this is one of the best tools for the technician! Removal of capacitor c31 on the t-con board (dc/dc power supply), shorted smd. circuit worked fine without it! AnisioH
LG 21FU4RL
Arming and disarming, generates and then cuts R815=91k and r843=39k open I replaced and ran to another one Antonio Carlos (Eletrônica Renascer)
LG 42PX4RV
Image with grain C77(10nf) defective on the ysus board Replace capacitor Mário Pereira
LG RP21FD10
When plugged into the socket it gives just an oscillation as when it turns on and the stand by does not light up; Turning it on and off several times, sometimes it turns on, and when you turn it off, it doesn't turn on again. Sometimes it even felt like cold welding, out of nowsound the standby would come on but then go off. When analyzing the power supply, I didn't find any damage to any component, but when testing the d802, I found a current leak and the standby LED came on after replacing it with an FR05 diode, but the TV still didn't always turn on when pressing the power button, So I also replaced the d810 with the same one and it worked perfectly. Replace the components mentioned and move on to another device. Jailson Lima
LG 20CB25
Burned horizontal transistor(tt2170) Replace for d5024 if you don't find it original and run for the hug digital system
LG LG LCD 29""
It turned on, tsound was normal sound, the lamps came on but the screen was white with no image Regulator from 3v3 to 2v5 on tcon in short I couldn't find any regulator with the same specifications so I put a 10r resistor between pins 1 and 3 and the voltage was 2.41v and the TV was like new. Eduardo Luis Vinoti
LG 32LN540B
TV turns on normally, the LEDs turn on and the screen turns gray C104 and 103 shorted And replace c 104 and 103 on the display ruler and go and test the é nor later Rubens P afonso
LG 21FU4RL
Arming and disarming R806=39k aberto I replaced and ran to another one Antonio Carlos (Eletrônica Renascer)
LG 21FU4RL
Totally inoperative charge retained in the power supply capacitor Photo coupler and r842 I replaced the photo coupler, the TV turned on, the stand armed and turned off then I replaced the r842=27k, replaced it with a 33k one and the screen was brand new Antonio Carlos (Eletrônica Renascer)
LG 50PB560B
LED blinks but doesn't turn on Avaria na y-sus capacitor c204 (150/35v) with leakage. Replace capacitor WELLINGTON
LG 50PB560B
TV does not turn on and the stand-by LED is blinking, the T-Con controller board LED is also off. I tried running auto gen which also didn't work. I found the electrolytic capacitor on the y-sus board position c204 at the bottom of the board 150mf 35v in a direct short. I replaced it and it worked perfectly. Invision Assistência Técnica