Lg Repair Tips

Search: lg
Results: 4929

Make	Model	Symptom	Problem	Solution	By
LG	RP20CB20A	Has image + no sound	This model has a headphone jack, which was defective.	I did a jumper on Jack and ran for a hug	fernando timbauba PE
LG	21FJ6RB	Vertical shaking wanting to close	Very critical defect was difficult to discover due to a lot of patience on my part I discovered a polyester capacitor hanging on the main IC cap 512 .474j .63v there is no point in measuring it on the capacimeter it measures right imagine! And just put on a new one and run for a hug, God and a hug from you, my technical friend.		fernando timbauba PE
LG	RP-21FE85G	Turns off randomly, after turning it on it doesn't stay on for more than 10 minutes.	Defect occurred after burning fly back and tr.horiz.	When you replace the fly back with a braz alfa and such a defect arises where the TV keeps turning off without an apparent defect, with the components that make up the monitoring of the abl being good (resit. and diodes and transistor itself), the value of fr401 de1r2 3w decreases to 1r 3w, the defect will be remedied. It is due to the difference. of res. bras alfa fly omics in relation to the original.	ELETRÔNICA ESTUDIER
LG	21FX5RL	Vertical partially closed, with normal sound	Deflector had part of the winding open due to oxidation		Bruske
LG	MCD503	When pressing open on the CD it indicates lock on	Future client	Press stop on the device and rew using the remote control, press together for ten seconds	ars
LG	HT302SD	Reader runs to the edge and crashes	Reader provided by LG with wrong code	Original (5fs) supplied (5fv) is not compatible!!! Only (5fs) works!!!	ars
LG	29C85	When changing the trans. horizontally the TV works, but turns off with a clear image	R831 changed (horizontal output overcurrent detector), to ensure, place 3 1 r resistors in parallel in place		Ronie Grein
LG	CP-14B86 SC-023A	Contrast does not work	Diode d502 shorted or open	Sorry for the TV model and cp-14b86	This email address is being protected from spambots. You need JavaScript enabled to view it.
LG	CP-1485	Contrast does not work	Diode d502 shorted or open		This email address is being protected from spambots. You need JavaScript enabled to view it.
LG	CP29C85	Reduced frame on the sides does not regulate horizontal width on trimpot vr400	Open 3r3 resistor r436		oltecti
LG	CP29Q12P MC996A	Excess width	Change ci smd 4558 of board h size position ic401		oltecti
LG	29FXCL	Excessive width and when you see the osd it looks like it is inverted on the screen	R 412 7k5		JOSÉ GUSMÃO
LG	42PX5DUP	Dark image after 5-10 minutes becomes a little lighter not much	Reaplaced z- sus board part number #6871qzh047b		Thomas Acoreano
LG	RP-21FD15BRS	Turning off	Defect in the abl, disconnect the base of q16 to check if the symptom ends. if yes, check the entire abl, probably there is a resistor changed in the abl		DEBIQUE (ELETRONICA ROBSON)
LG	21FU1R	No sound with image beauty	TV erased the memory This happens when the TV takes on water, changing the memory sometimes does not solve the problem because of the different TV TVC model programming.	Enter service mode, replace to stereo 2 press ok on the remote control, to enter service mode; Press menu on control and TV together then press menu to replace address vol+or- can+or- to replace address then press ok good luck	marcos melo CASCAVEL CE
LG	42PC1RV PLASMA	It doesn't work. When it turns on, the white LED flashes for a few seconds and turns red. (stand by)	Q 801. c 3198.	Replace.	This email address is being protected from spambots. You need JavaScript enabled to view it.
LG	29CC2RL	Does not turn on without voltage horizontally and engaging the relay	Change the 2 optocoupler and solved		KAIRO MT
LG	CP 20B 85	TV turns on with all the currents and then red predominates as if the resistor responsible for red had opened	Tracker Socket Two Tubo		eletronica havai
LG	20CD2R	Doesn't start	Transistor q402 tt 2170 shorted, also change c 406 2.2x 160v and first check the power supply, which must have 110 v		CARLOS AUGUSTO
LG	230CD2R	Doesn't start	Transistor q402 tt 2170 shorted, also change c 406 2.2x 160v and first check the power supply, which must have 110 v		CARLOS AUGUSTO