Panasonic Repair Tips
Search: panasonic
Results: 2900
Results: 2900
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PANASONIC |
TC20PLCTV21L4
|
Dead | Q1001 | ||
| PANASONIC |
TC14G8/20G8
|
Dead | C820 | ||
| PANASONIC |
TC29V60
|
Closes the frame a little by giving it shine | Sketch | ||
| PANASONIC |
TC29V60
|
Dead | Ic801 | ||
| PANASONIC |
TC14C4/20C4
|
Burning f801 and f802 | Ic802, replace c812 | ||
| PANASONIC |
TC14D1/20D1
|
Folding the image at the top | C412 | ||
| PANASONIC |
TC14C1/20C1
|
Loud sound and won't change channels | R881, r882 | ||
| PANASONIC |
TC-14C2/20C2
|
Unstable vertical | C410 | ||
| PANASONIC |
TC-14C2/20C2
|
Dead and beeping | Flyback | ||
| PANASONIC |
TC-14C2/20C2
|
Image shakes when adding volume | 16v power supply low and r863 | ||
| PANASONIC |
TC-14C2/20C2
|
Image very bright and does not darken | 19 | ||
| PANASONIC |
TC20C6
|
Inoperative, relay knocking | Open r802 or r803 (470k) | ||
| PANASONIC |
TC-29V50B
|
Burning of ic802(str), d184, c812, q804 | In the first production batches the resistor r841 was assembled very close to the heatsink, which will cause cold solder heat dissipation and oxidation at its terminals. as this resistor is located between the drive and the base of the power transistor, this bad contact will cause IC802(str), d814, c812, q804 | Solution: 1) after the burned components are replaced, the resistor r841 must be removed, checking that its value has not been replaced, if it has been, it must be replaced. if its value is ok, its terminals should be sanded and resoldered into its position on the board. 2) please take this countermeasure for all devices that pass through an authorized workshop for maintenance, whether the device is presenting or not problems at the power supply. | |
| PANASONIC |
TX 25MD3E
Euro 2M |
No image dark | Failure | Bobine l202 na f. i. e tuner | |
| PANASONIC |
SA AK 27
|
Not for tuning, does not identify CD, does not produce sound | R521 = 4.7r line of minus 30 volts | Sub r 521 = 4,7 r | |
| PANASONIC |
SA AK 27
Hi Fi |
Not for tuning, does not identify CD, does not produce sound | R521 = 4.7r line of minus 30 volts | Sub r 521 = 4,7 r | |
| PANASONIC |
TV111
|
Queima do stk73907-t | 1-add thermal paste, 2. add a 130pf / 3.6MΩ capristor code. exng131p365 between each ac line with cold ground. solder the capristors underneath the print and glue them with silicone or hot glue. 3. add a code 10nf capacitor. ecqm4103jzw in parallel with c805. solder the capacitor underneath the print and glue it with silicone. 4. Add an insulated wire jumper between point A13 and tuner ground. | ||
| PANASONIC |
TC-21V50B
|
Queima do stk73907-t | 1-add thermal paste, 2. add a 130pf / 3.6MΩ capristor code. exng131p365 between each ac line with cold ground. solder the capristors underneath the print and glue them with silicone or hot glue. 3. add a code 10nf capacitor. ecqm4103jzw in parallel with c805. solder the capacitor underneath the print and glue it with silicone. 4. Add an insulated wire jumper between point A13 and tuner ground. | ||
| PANASONIC |
TC-20G7
|
Queima do stk73907-t | 1-add thermal paste, 2. add a 130pf / 3.6MΩ capristor code. exng131p365 between each ac line with cold ground. solder the capristors underneath the print and glue them with silicone or hot glue. 3. add a code 10nf capacitor. ecqm4103jzw in parallel with c805. solder the capacitor underneath the print and glue it with silicone. 4. Add an insulated wire jumper between point A13 and tuner ground. | ||
| PANASONIC |
TC 20A12
|
Turns off after a few minutes | C 520, de 220/6,3v |