Panasonic Repair Tips

Search: panasonic
Results: 2900

Make	Model	Symptom	Problem	Solution	By
TV PANASONIC	TC-20C4 TNP1970776-9		The cause is a power supply capacitor c812 47 by 63 v dry		CUNHA753
PANASONIC	TC20RM10L	Turning off	Changed power supply going to 180 volts	Replace zener d 821 in the photo-coupler circuit	MARCELO DE CASTRO
PANASONIC	TC14C	The image kept disappearing, going out of tune	Diode d1114	Replace	EletroClaudio Aguas Belas
PANASONIC	TC 29 KL 5	A luminous streak in the center of the screen, in a vertical direction.	Causes c563=390 nf , totally out of capacity.	It was replaced and resolved.	Armando,Eletronica EvoluSom
PANASONIC	29KL05 NãO	Nothing works	Open components	Panasonic 29kol doesn't turn on, it was replaced bu 4508dx-r520 r251 d557 c563 t 752 and it got a screeching fleyback cause c519, and everything was perfect	luiztvsom
PANASONIC	TC-14A04	High power supply (does not regulate) - when you plug the device into a socket, the voltage above c-863 exceeds 150v and trips.	D-821 - shorted		This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	20C6	Vertical fold at the top of the screen	C-461 (ceramic capacitor - 104 - 100k)		This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	TC14A10	Vertical closed 5 centimeters at the top and bottom	27k r425 resistor near the altered micro	Replace	EletroClaudio Aguas Belas
PANASONIC	29KL05 GP3	This TV came with the horizontal closed, I changed the c 563 394jx250v, opened the horizontal, but tsound were bands on the side like the flex arc	Replace c 560 394jx400v	Replaced it works beauty	claudinei aparecido ferre
PANASONIC	TC 29 G 11	TV with the screen off and without sound, I realized that it was starting and going into protection.	Causes short vertical output ci,la7840.	It was replaced and it looks great.	Armando,eletrnica EvoluSom
PANASONIC	TC20C7	Hiccups, tries to call, without + b, hits the relay.	D 806 as leak		Lima
PANASONIC	TC-20A10	With screen drizzling, no channels tuned	Diodo zener 1170	Toca do d 1170 6,8volts	astel eletronica sousa
PANASONIC	TC-20G9	Does not turn on when activating power	When resolving it, it worked after it cooled down, the defect came back, I turned off several protections and sometimes it turned on, then I put the chassis in the fridge for an hour then it didn't turn on, but after several tests I discovered that the 804 was leaking, I put a bf 423 and that was it.	I put bf 423 pnp	sousa
PANASONIC	NN7858BH	Turns on and when you press start it disarms	Lack of grounding from the board to the device housing	Do the grounding	digital system
PANASONIC	TC20A10	The power supply voltage drops and returns to normal, (the normal image then suddenly decreases and returns to normal.)	Change ,d 805 , at the power supply.		donypinheiro
PANASONIC	TC-29A8 6NL	It does not activate, when pressing power it hits the relay and goes into st by - protection.	Check tr collector voltages. horizontal.if you don't have it and it is in good condition, disconnect pin 10 of the fly back and see if tsound is voltage in the tr.horiz. collector, if it is approximately equal to +b.replace the fly back	Replace fly back.	OLIBIO - ELETRONICA ESTUDIER- CANOAS RS
PANASONIC	29A8	Contrast does not work	R 564 / r563 abertos		WARLEY CESAR
PANASONIC	TC 29KL05	TV doesn't work - activates protection	R519 e q551	Replace r519 -1r x1w e q551 - c5902	EMERSON RIBEIRO
PANASONIC	TC-29A8	Hang up	Image increases in luminance and turns off.	Get in	LOU
PANASONIC	TC-14A04	Does not turn on heats r810 fuse type @@@	D810, r810 resistor may be open for heating mode		ELETRONICA ARNI-SC / LEOBERTO LEAL