Panasonic Repair Tips

Search: panasonic
Results: 2909

Make	Model	Symptom	Problem	Solution	By
PANASONIC	TC-P50G11B	Turns on, but turns off after 10 seconds, then the red LED flashes 11x	One of the fans, it was spinning normally, but tsound was noise when spinning	You have to replace it, testing it turns, but you have to replace it.	Denis Cardoso
PANASONIC	TC-L42E5BG	Power on is already flashing error 3 flashes	Processor bga.	I didn't solve it, I don't do reballing, I only discovered the defect because I heated it with a hairdryer on the processor and the TV started working again, after it cooled down it gave the defect again...	MIGUELTV
PANASONIC	TC20RM10	Turn on and off	D. 1132 5v6 curto	Replace the same	This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONIC	TC-L42U30B	TV turns on, with image, but soon distorts causing horizontal bands, black and white stripes across the entire screen, turning off.	Main board defect, short smd capacitor, on ic5000 on pin14 smd capacitor 1uf leak or short, board does not have silkscreen.		RNSPTEC
PANASONIC	TC-L42U30B	TV turns on and after a few minutes turns off by itself	Cold solder on d836 - rectif diode. (bridge) 800 v 6.0 a (correction of the diode code indicated in the previous one)	Redone the solders on d836 (b0fbat000017) - rectif diode. (bridge) 800 v 6.0 a	Luiz Cunha
PANASONIC	TC-40D400B	The LEDs turn on but no image	Leaky capacitor cd33 on the vecom board (this was in my case)		ELETRÔNICA DVN
PANASONIC	39AS600B	LED current reduction	Remove the smd resistors 144 to 148 and place just one 0.22r can be large taken from scrap, the voltage drops from 38 to 35 volts in each LED driver, measure before changing to be sure, it is 100%		reginaldo moronte,eletronica junior caldas novas
PANASONIC	TC-32DS600B	No image on the display, just light around the display.	Smd capacitor c62 on the t-com board changed, killing the main board voltages 12 and 5 volts.	After removing the c62, the voltages returned to 12 and 5 volts on the main board and image on the display.	Eletrônica Cled Tec Cell
PANASONIC	TC-L42E5BG	Standby LED flasher, 1x/ change the LED bus	Reduce the current, remove r120, r121, rr122, I replaced it with a 20k one, it was ok		Eletrônica COMETA
PANASONIC	TC-32A400B	Dead tv. standby off	Ci tpc8132 - position q7502 on the power supply board		George Luís
PANASONIC	SB WA730	When turned on, it turns off in seconds and shows error f61 on the display	Open diode ref. d2812 I put a 1n4007 rectifier in place and it worked fine		Eletronica Pereira
PANASONIC	TC-L32C5B	Doesn't work	R7314 with glue leak	R7314 killed the voltage for transistor q7303 due to leakage in the resistor glue, preventing the transistor from saturating.	eletrofepar
PANASONIC	TC -20KM03	Turns on and off, LED flashing.	R631(560k) open.		MARCONES DE ARARIPINA -PE
PANASONIC	TC -20KM03	Alloy generates high, and cuts.	R631 (560k) open.	Replace r631. close to the 180v connector	MARCONES DE ARARIPINA -PE
PANASONIC	SA-AKX220	Does not turn on, when clicking power, voltages on the main board appear, and then drop	Corrupted eeprom data.		Davi.sls
PANASONIC	TC-L42E5BG	Blinks 1x standby LED LED bus defect	After changing the LEDs, reduce the LED current	Remove r 120, r121 and r122 and place an 18k resistor in place current drops from 104ma to 66 ma	Ariel Santos
PANASONIC	TC-20G9	With green sound and image	15k open resistor on tube socket board		BICHARA SARQUIS
PANASONIC	TX-P46G30E	Flashes 14 times relay hits and disarms sometimes the fans start for a brief moment	Cold solder on the power supply board	Resolder compromised jumpers and solders and run for the hug	NCTIC REPAIR
PANASONIC	TC-40C400B	LED current reduction	Retirar resistores smd r7802,r7803,r7804		reginaldo moronte,eletronica junior caldas novas
PANASONIC	TC-P50G11B	TV turns on normally, after a few seconds it turns off with the red LED flashing 11 times	One bloated capacitor (position c253 of 1400uf by 220v) and two with half-life of use (position c353 and c355 of 820uf by 80v) all on the power supply board	Replace the c253 with a 1500μF capacitor at 250v and the c353/c355 with a 820μF capacitor at 100v and the TV started working normally again	FridayTechLab.