Panasonic Repair Tips

Search: panasonic
Results: 2909

Make	Model	Symptom	Problem	Solution	By
PANASONIC	TC-14A04P	On and off and the LED kept blinking	C403 electrolytic 50v 22uf I just changed it and it was sound. This tip is new since I had to figure it out without help because it wasn't available on the internet	Was replaced. never remove the protection if the voltage is above 140 volts	genilson oliveira
PANASONIC	TC-39AS600B	Does not even turn on the standby LED	Ic-5000 an34043a	Replace for the same one. good luck!	Evando Viana
PANASONIC	TC-40C400B	Turn on the LED bars, they light up, blink a few times, then they turn off and the stand by status is blinking red.	Problem in the fets line that powers the LEDs	On the p3 connector that goes out to the LEDs, jump pin 3 to pin 4, if that doesn't work, jump pin 5 to pin 6. I already took several and did this procedure and it solved it..	Eletrônica Evolução
PANASONIC	AKX440	Doesn't start	Ic 1003 regulator 6v short causes short in usb ic2501 2502 remove both, place a 10r resistor between pins 1 and 6	Replace do ic 1003 tps54240	marcos melo cascavel ceara zap 85984138041 ajuda meu pix 76731162353
PANASONIC	NN-ST354	Direct light and fan	SMD open resistor (202 2k you can put 222 2k2), it is after the SMS diode that comes from the micro switch with blue wires connected to the board		reginaldo moronte,eletronica junior caldas novas
PANASONIC	TC-L32C30B	Turning off, switching off, with noisy power supply, low power supply	Input filter capacitor	Replace capacitor c7212 120/450v	VALDENIR ( TECVIDEO )
AP.SOM PANASONIC	AKX710	Bluetooth failing	Reset and solved the problem.		Carlos Rocha.
AP.SOM PANASONIC	AKX710	Bluetooth failing	Reset and solved the problem.		Carlos Rocha.
PANASONIC	SA-AKX 10 BIJODA001501	Doesn't start	He called and he didn't answer anything		José Edivan Batista
PANASONIC	TC-L32E5BG	I changed the TV card, and the new one doesn't tune channels	Changing the main board, but not tuning channels		Rafael de Lira
PANASONIC	TC-40DS600B	Burned LED panel (03 rulers with 08 LEDs each ruler and the LEDs are 6v) and each LED has 6.6 volts on top of it....	Modification to reduce current (link on YouTube the nel 350: https://www.youtube.com/watch?v=fliqgp62tps) and then it deals with the tc-40d400 but the power supply is very similar to 40ds600b	Modify resistors r7837(1r), r7835(1r), r7826(1r), in my case I modified them to 2r7 and the voltage dropped from 42 volts to 38v. detail that the manμFacturers are dishonest and when you turn on the TV the voltage comes at 48 volts, then the pwm corrects it and drops to 38v, turn it on today, turn it on tomorrow and tsound it goes... in other words with this voltage above normal over time The LEDs will definitely go out...	MIGUELTV
PANASONIC	TC-L39EM6B TC-L39EM6B	Turns on with backlight without image	Usage time	Main board with pnl-12v line with low resistance - I looked until I found a smd c4002 capacitor with 24.6Ω	@Nelson.g24
PANASONIC	SA-AK110	Take out. CD tray opens and won't close.	CD mechanism out of time or reset by unloading the elco close to the processor on the front plate.		jr_TEC
PANASONIC	SAAK110	Take out. CD tray opens and won't close.	CD mechanism out of time or reset by unloading the elco close to the processor on the front plate.		jr_TEC
PANASONIC	TC-L47DT50B	Does not turn on, inoperative	I replaced all the photo couplers in the power supply, it worked perfectly again		Eletrônica JJ
PANASONIC	TC-32A400B	When turning on the power, the green LED flashes quickly for a few times and then the red LED starts flashing in a loop, once and pause, once and pause....	So error 1, I put a LED kit on the outside without opening the TV and it resolved it, then the LED bus failed.	Replace panel/led kit	MIGUELTV
PANASONIC	TC-32ES600B TC-32FS600B	Pcf with around 300v, voltage on pin 3 of the pc7300 zero and some voltages present on the secondary but it does not turn on or stand by.	Check for a possible leak in d7307 (primary), it could be the glue or the component itself.		electronicssupplyparts - Gramado/RS
PANASONIC	TC-L50E6B	TV turns on and backlight turns on, but no image +b and t-con 12v fuse ok	On the pci t-con it had lp1 with a defect in the solders and it did not generate 3v3		YouTube Direto no defeito
PANASONIC	TV 14C4	Blowing fuse	Capacitors c813 (10uf 50v) and c812 (56uf 50v), both without liquid or exhausted.	After the replace everything was ok.	George Pontes
PANASONIC	TC-55AS700B LA51	Does not turn on, backlight flashes and activates standby LED protection flashes red 1x	See possible problem with the rulers, each bank of LEDs lights up with 43v. If the LEDs are ok, check the power supply board. Tsound are 6 smd tr on the power supply board responsible for regulating the negative of the LED banks. One of them may have a short circuit, measure carefully as they are pnp transistors	Replace the shorted transistor 2sb1181 or replace the power supply lacquer if you can't find the transistor to buy	rafaelmoraes99