Panasonic Repair Tips

Search: panasonic
Results: 2900

Make	Model	Symptom	Problem	Solution	By
PANASONIC	NNS 62 BH	Does not heat up and turns off before the programmed time	Oxidation on the processor behind the display	Remove oxidation	Laercio umuarama
PANASONIC	TC-32FS500 KÒD+L070	The LED turns on and off	Black screen		Marc kerlin Fenelus
PANASONIC	NN-G55BH	After pressing the "on" button, it works for a few seconds and stops.	Internal sparking due to peeling paint	Repaint with suitable paint.	Ferraz
PANASONIC	49D400B	TV with a horizontal list on the screen that left a defective image. shaking and frozen. the other part upwards was normal. works perfectly.	Display ruler on the right. I isolated 10 liters from the beginning from right to left. starting from the first 1. (this after a lot of trying) turned out pink but worked perfectly
PANASONIC	TC-L42U30B	The LED blinks indicating a backlight failure	The ants made a nest in the connectors and the TV protected it and wouldn't stay on	Opening the display and cleaning it solved the problem.	antonio nobrega patos pb
PANASONIC	TC-L42E5BG LA35	Does not tune channels and all HDMI inputs with interference, image blinking	1.8v low or high supply on the main PCI.	Changing the adjustable regulator ld1117al-ad condition ic8702 is located below the microprocessor heatsink.	rafaelmoraes99
PANASONIC	TC-L32C10B	Disappearing image with a blink	Bad bulbs or bad contact		Cabeça
PANASONIC	40FS600B	Red LED does not turn on, flashing continuously once	Short on the main board and the power supply board, causing the board to release 16v directly when disconnecting the power supply cable from the main board	Changing a ceramic capacitor close to the connector that receives the cable from the 16v line power supply. changing a transistor on the 16v line supply board, in my case the transistor was visibly blown.	ELETROSANROS
PANASONIC	39A400B	TV working but image blurred, full of return stripes and colors. tremendous image.	Cockroach dirt. several capacitors and smds in shorts.	Display replace
PANASONIC	SA AKX10	Does not turn on inoperative	Power supply that feeds the audio output with no voltage on the secondary stdby power supply ok oom 3.3v in my case checking all the capacitors tsound was no defect I took the main IC strx6759 from another device working and it still wasn't resouble I returned the original IC I did more tests and nothing solved, I checked all the strx6759 coupling smd components, they were all good, it took a lot of work lol	To solve this case, it was very simple. I remembered that I already got another sound device, which was LG, which used this same ci on the strx6759 power supply that powered the amplifier and it turned on, but without audio, as it did not have power on the amplifier board, good a The solution was to place a 10k resistor on pins 3e4 of the photocoupler pc5720 panasonic sound, which compares the power supply together with the ci tl431 in the lg sound the same procedure was done ok	rubertan
PANASONIC	TC-L32C30B	Does not turn on red LED flashes 9 times	Ci sound amplifier short lv4924	Replacing the lv4924 sound ci	ELETRONICA KLEIN
PANASONIC	TC-32CS600B	Turns on without image with sound and then turns off	Burnt out backlight LEDs. gives the impression of another defect		Stiltec
PANASONIC	TC-32CS600B	League without image with sound	Burnt out backlight leds	Replace the bars	Stiltec
PANASONIC	SC-HT75	Language but the sound disappears after a few seconds, the panel remains lit.	Dc on the left output of the surround speakers, system goes into protection	Changing the output ci or isolating the left surround output, pin 1 of the audio output ci.	José Dias
PANASONIC	TC-L32C5B	Turns on, turns on the backlight momentarily and turns off, indicating the 3-blink error code on the LED.	Check for a short in the 2 smd capacitors under board a (main board) they are close to the silkscreen "q4153" going diagonally to the right, it could be the top or bottom capacitor, don't forget to change the smd fusistor that is connected to series on the line, it has the letter "n" written on the body, the capacitors must be replaced, the capacitance is 5uf each, use larger smd capacitors so they will have a higher insulation voltage.	Replace all components and check for shorts. (tec edfersom. varjota-ce)	Edfersom
PANASONIC	TC-L32B6B	TV keeps flashing red, voltage is 16v, plugs it into socket, it appears 15.4v then goes to ov	LED bar burned out, TV won't turn on, screen off, no sound		JOAQUIM ROSA
PANASONIC	TC-14A02	Does not connect power supply +b less than 140 volts	Cause diode.	Replace diode d1132 or remove from board	renildo
PANASONIC	TC-32A400B KM26	TV completely inoperative, stand-by LED does not light up and power supply voltages are absent.	Remove the jumper resistor vj2001 and place the TV in the socket and if it turns on, check for a short in the audio output... in my case the problem was in the shorted capacitor c4901.		ROBERVA1
PANASONIC	TC L32-B6B	Does not turn on, vd led blinks then comes back on and vm stand by led stays blinking	Defective led bars.		KRUL
PANASONIC	40FS600B	Blinking red LED non-stop	Capacitor and regulator near the usb port in short (ic8453)	Remove and replace them	Andrei (051)991421340