Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
21PT9467C/78
SK4.1L |
When changing the fly back, the xt mark when it heats up the image starts to shake. | Put a shim on the fly back ferrite. | fgalvim | |
| PHILIPS |
20PT424
|
It doesn't turn on, the LED flashes and the protection is activated! | C2409 47x160v bad and fly back raw between pins 2 and 3 ov2094/b1 | Replace both | orlando lott |
| PHILIPS |
40PFL5606
|
Customer reported that device stopped turning on after moving from one location to another | Does not turn on, only 3vstb voltage | Poor contact in the power supply connector on the signal board. | neweletrotech ctba |
| PHILIPS |
FWM 452X/78
|
No sound | Remove q601 q602 (mute) | Bruno nicacio | |
| PHILIPS |
20PT4331
L03.1L |
When you turn on the sound it's normal, after 10 minutes the sound cuts out | Capacitor 2833 | Replace the capacitor | JMS ELETRONICA |
| PHILIPS |
29PT9467C178
|
TV turning on with portrait line and 2 horizontal stripes and turning off | Image with horizontal lines and stripes | ||
| PHILIPS |
14GL1015
|
When turned on, the channel sounds, but the image has open screen-like retraces. | Capacitor c2410 on vertical pin 8 open 100/25, change and go to the hug. | jefferson godoy | |
| PHILIPS14 |
14PT316A/78R
|
No image green screen | Fusion no image green screen | aluizio | |
| PHILIPS |
14PT110A
78R |
Doesn't start. | Exchange c2551 and c2448 sold out. | jayjunior | |
| PHILIPS |
14PT4131
|
No audio, no sound when turned on, it made a very low noise, it didn't activate the audio, not even with your finger. | C2444, it was well heated, I put 1000mf/16v | Other similar models pt3131 ... 4331...3331 | Alextecnico |
| PHILIPS |
29PT4640
L01.1LAC2K3 |
Dark image with traces and small clicks on the tube plate, (there are several clicks per second, 5 times or more) and these clicks are reflected in the image, that is, when the click occurs the image becomes clearer. | I found r3481 and r3482 open, I also changed r3465 and the image improved but there were still crackles, but it was because of the screen being out of adjustment, it was just a small adjustment and that was it, the crackles disappeared and the image was perfect. | ||
| PHILIPS |
DVP 320BK
|
It only stays on standby, LED indicator flashes or turns on and off in seconds | Low supply voltage, 7v5 zener with leak and exhausted capacitors on the secondary | Replace 6622, 2221 and 2210 | Felipe Farias |
| PHILIPS |
29PT554A
|
Doesn't even turn on the stand by LED | Changed d6540 had 5 volts on pin 1 of ic 7520 | Replace d 6540 | juci |
| PHILIPS |
FWM593
|
No sound | R611 e tr q632 | Just replace it and move on to another one. | eletronica vieceli |
| PHILIPS |
20PT122A
|
Av doesn't work | Enter service mode ground pin 1 memory | Replace to av 01 | ELETRONICA MAURI JUNIOR |
| PHILIPS |
CTN-BB
|
Does not do standby | Replace smd transistor position 7601 | Ruyzovich | |
| PHILIPS |
CTN-BB
|
Red image with return lines | Replace smd transistor position 7644 | Ruyzovich | |
| PHILIPS |
CTN-BB
|
Does not start LED blinks | Replace 12Ω resistance in power supply position 3521 | Ruyzovich | |
| PHILIPS |
CTN-BB
|
Does not adjust contrast | Replace resistance (3460) of 10k | Ruyzovich | |
| PHILIPS |
CTS-AA
|
Vertical problem, image shrinks when changing scene | Change r3461 from 8k2 | Ruyzovich |