Philips Repair Tips
Search: philips
Results: 14209
Results: 14209
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
L6.1
|
Focus not optimal | Check/replace lot l5422. | ||
| PHILIPS |
L6.1
|
Does not find all programs during search. | Replace microprocessor ic7600 with version l6notxt-2.0, codenumber 4822 209 13085. | ||
| PHILIPS |
L6.1
|
Does not find all programs during search (for txt and no-txt versions) | New software will solve this problem. change software into new version;codenumbers are still identical 4822 209 14646:txt 1 p mono pan-european l6txtmoeu-1.1 3/4 keys:saa5290zp/072 4822 209 15425:txt 1 p mono greek/turkisch l6tmogt-1.1 | ||
| PHILIPS |
L6.1
|
Dead, loptr s/c | Replace c2503 with 33nf 250v (532212142489), r3512 with 68k, d6510 with 12v zener | ||
| PHILIPS |
L6.1
|
Dead - chopper s/c, mains fuse o/c etc | Fit repair kit - still dead with squealing from tfmr - pin hole in but11ax encapsulation (measured ok out of cct) | ||
| PHILIPS |
L6.1
|
Cross picture (you can partly see the picture of the next station) | Add new saw filter (ce marking module = 4822 212 11352). this filter can be switched between bg and dk. how to adapt the set: * remove saw filter on position 1001 and replace by ce marking module. * solder the black wire in the hole mce1 near .p | ||
| PHILIPS |
L6.1
|
Cracks in sound during fast changing of picture from black to white. | New solution: replace 9001 by 39Ω nfr = 4822 052 10399 and add 470 uf between 9001/3013 and ground (470 uf=4822 124 80791) | ||
| PHILIPS |
L6.1
|
Cracks in sound during fast changing of picture from black to white. | Change c2425 to 2200uf 25v.codenumber 4822 124 42449. remarks : this only occurs if contrast is at maximum. | ||
| PHILIPS |
L6.1
|
Colour flashes appears or loss of chroma in secam standard | Change r3433 (see diagram a1) from 39k to 56k service code 4822 051 20563 | ||
| PHILIPS |
L6.1
|
Code-number supply-repair kit l6.1 | Code-number supply-repair kit l6.1 ---------------------------------- in the service manual of the l6.1 the codenumber of the supply-repair kit is missing. the code-number is 4822 310 10663. | ||
| PHILIPS |
L6.1
|
Bending picture depending on its white contents. | Change r3420 (see diagram a1) from 12k to 18k (service code 4822 116 52251) iris code : 1353 | ||
| PHILIPS |
L6.1
|
Bad focus or focus varies in a new set or after crt replacement | Possible solution: short circuit the focus and the g2 pins of the picture tube with the aquadag coating. switch the set on for approximately 5 seconds. after this return the set to its original condition. check if the focus adjusted normally. if not repla | ||
| PHILIPS |
L6.1
|
After a while white screen. | Check/replace lot l5422. | ||
| PHILIPS |
L6 SERIES
|
Dead | Chopper fet, sops kit & ht smoother c2515 47µ 200v | ||
| PHILIPS |
L2.2AA 29PT828C/05
|
Dead - 5a fuse in plug o/c | Mains rect cap arcing 220µ 385v | ||
| PHILIPS |
L01.2EE 21PT4457/05
|
No red at sw on then reverts to st/by | R3316 68r 1/2w o/c, tr7311 bf422 s/c b- e - on crt base | ||
| PHILIPS |
L01.1 28PT5107
|
1cm noise band from top to bottom lh side of screen varies with brightness & chan | D6460 by 228 over loptx | ||
| PHILIPS |
L 6.2 / 6.3
|
Int locks up - no can change or switch on/off | Replace 7505 (bc337-40 it is close to power transformer secondary side. (ref leif) | ||
| PHILIPS |
L 6.2
|
Bu1508ax has short life | Orange cap in deflection pcb+ l 5420+.l 5421 in base-circuit | ||
| PHILIPS |
L 6.2
|
Horizontal line | If +25 volt missing on 110 degr. module,then check d6907, this can be s/c ( use only byv 27-400) also check r3908 isn't touching spring for t7904 & check r3928 1r |