Philips Repair Tips

Search: philips
Results: 14210

Make	Model	Symptom	Problem
PHILIPS	G110-S	Set dead; during switch-on, led momentarily on with amber light.	Two possible solutions: 1. replace up ic7200 by tmp47c634n-r364 (4822 209 31492) and keyboard pos 1210 by 4822 218 21032 2. upon switching on, if the set is hung, do the following initialising for the up - switch off the set. disconnect pin 41 of up
PHILIPS	G110-S	Picture jumping when switching from pal to ntsc m	Place on copper side across item 2503 +ve to +ve and -ve to -ve of item 2503 a capacitor of 1uh 20% 50v (4822 124 40242). remarks: introduced in production in week 9252
PHILIPS	G110-S	Bad picture sharpness	Only for 21gr6766/56, 25gr6766/56, 28gr6776/56 serial numbers sv009025 or lower change 3481 smd to 510r (4822 051 10511) change 3483 smd to 100r (4822 051 10101) change 3484 smd to 1k (4822 051 10102 for 21" sets: on the conductor side of the main p
PHILIPS	G110-PTV	Preventive action	Preventive action . after replacing a projection tube, the deflection coil may shift downwards. to keep the deflection coil on its correct location, the coil should be glued to the new projection tube. adhesive 4822 390 30066 should be applied between t
PHILIPS	G110-PTV	Horizontal adjustment does not work. picture too wide.	Elco 2549 (10uf) capacity reduced. replace by code 4822 124 80275 (mechanically bigger).
PHILIPS	G110-PTV	Excessive width	In the case of excessive width, it is possible that c2549 (east/west circuit) is low capacity. to improve reliability an alternative type of capacitor should be used as a replacement. however, the dimensions of this capacitor are different from the origi
PHILIPS	G110-PTV	Excess width	C2549 10µ 50v in ew corr cct
PHILIPS	G110-PTV	Addition to parts list	Addition to parts list. the eht cable crt to splitter (3) is available under code number 4822 320 20192. please add to the parts list in the g110 ptv chassis service manual.
PHILIPS	G110 25GR9762	Int blows wickman fuse 1534 esp when chassis in place	Dry joints pin 2 e/w tx
PHILIPS	G110 25GR9762	Blows wickman fuse 1534 int	Dry joint pin 2 e/w trfmr
PHILIPS	G110 25GR9660/22B	Width excessive	Pot 3525 10k o/c
PHILIPS	G110 25GR9660/22B	No horizontal adj	Pot 3595 1k o/c, 2593-2594 caps both 10uf 63v leaky, resistor 3596 150r o/c & res 3502 8k2 heat stressed
PHILIPS	G110 25GR5764?05B	Pic randomly disappears with no txt - only lines	Fault on txt panel - could be coil l5803 which is unavailable or remove txt pcb so that the tv works minus txt
PHILIPS	G110	Won't start up - p.s squeals. voltages lower than normal.	Sound ic defective. after replacement, ps protection active- change also 7281&7282(bc848) near sound ic
PHILIPS	G110	Won't start up - p.s squeals. voltages lower than normal.	Sound ic defective. after replacement, ps protection active- change also 7281&7282(bc848) near sound ic
PHILIPS	G110	Wont power up unless pin 3 loptx dis'd	This is the 14v supply which feeds 12v reg. q7284 bc858 sm in audio prot stage was leaky
PHILIPS	G110	Will not start; +148v = +/- 20 volts	Fault suspected in line output stage. disconnect pin 3 of lot transformer. if +148v comes to normal and line drive is achieved; reconnect pin 3 of lot and try disconnecting r3281 (location d4 of pcb). if set starts up, suspect t7284 audio protection tra
PHILIPS	G110	Width excessive & varies with brightness	C2526 6n8 sm cap in ew mod cct leaky
PHILIPS	G110	Width at max or int (after loptx replacement)	R3525 10k width pot o/c
PHILIPS	G110	White area visible on right side of screen in ext1 mode of bl sets.	Remove the resistors 3462 and 3464. add a potentiometer of 47k (4822 100 11371) on the position of r3461.