Samsung Repair Tips
Search: samsung
Results: 3845
Results: 3845
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG |
PL43F4000
NA |
Dark image with reddish pigmentation | Power supply board, voltage va with 17.89vdc instead of 58vdc. short in diode d352 (sb3200), it is close to the 3 photo-couplers. | Robusto53 | |
| SAMSUNG |
50NU7100 50RU7100 49RU7100
|
Image only in the middle of the screen. like a strip of light in the middle of the screen with a normal image and the sides, everything is dark! | Burnt out LED bars and high current in the LED power supply. | After changing the LED bars, replace the r9201 and 9101 resistors with 4r7 x 2w resistors and sand the light-diffusing acrylic. | Samuel Silva |
| SAMSUNG |
PN51H4500
|
It turns on whenever it wants, I noticed that on hot days it turned on easier | Qq807 and qq806 at power supply | Replacing std5915 transistors | FelixClank |
| SAMSUNG |
PN43H4000AG
|
Tsound is no VA and VS voltage | Icm851 (tl 431 -smd) | Icm851 | Tibúrcio |
| SAMSUNG |
UN40J5200 AG
|
Burning led bus solution | Lower the LED current by removing the two low-value resistors of 2.3 homs and placing a 3.6 homs connected to the fet socket that powers the LED bars | And good luck | <small> |
| SAMSUNG |
UN32D5000
|
Whitish image | Defective tcon | Replace capacitors smd disc c625626627 one of them has a leak. I don't know the value, I took it from another tcon | oskarala |
| SAMSUNG |
32JH4205G
|
LED blinking and won't turn on. Sometimes it turns on the backlight, the Samsung logo appears and then it turns off and the LED flashes again. | Q211, 3.3v switch, power supply connector side on main. 3v goes in and 3v comes out. | Switch or jumper | joaomvjr |
| SAMSUNG |
PL42B450
|
Voltage vs low | Cs811 and cs847 capacitors swap which solves | Marcio Gomes | |
| SAMSUNG |
HT-C550/553
|
Doesn't start | Line connecting pin 4 of the oc2 coupler interrupted | milenio | |
| SAMSUNG |
LE32B450 BN44-00261B
|
Doesn't work. | Multiple components, replace: icp801s (fan7350), rp814, rp815(2 mω), rp816, rp817(1.5 mω), rp819(56 kω) | Rui | |
| SAMSUNG |
LN40B530P2M
H40F1-9SS |
TV turns on but tsound is no inverter voltage for lamps | Changed the PC802S photo coupler and the ATV turned on normally. | eletronica vf | |
| SAMSUNG |
UN32F4200
|
Weak blinking backlight. LED voltage does not steady. LED bars ok | After analyzing the entire circuit, I realized that the 2 volt voltage at the gate of q9102c was pulsing | I replaced zd9104 zener 15 volts on the gate line of q9102c. resolved. | |
| SAMSUNG |
T27A550
|
It doesn't turn on and the standby LED doesn't turn on either. | Power supply board with all voltages and when disconnecting the cable that connects the power supply board to the main one, the display LEDs light up. | The defect is in the power supply. (cm807) replace the same 47x50 volts. | eletronica cachoeira |
| SAMSUNG |
UN55F6800
|
It doesn't turn on, the relay keeps hitting | Open ds806 diode | Ds806 replacement | Arnoltec |
| SAMSUNG |
PL51F4500
|
TV turns on normally, after warming up, the image appears. | Cp822 on the power supply board when it gets hot it shorts out, change it | Replace capacitor | CLAUDIO |
| SAMSUNG |
LT 19B300
|
TV works normally, turns off and shows blue, green and red colors with no image | The 202 ci e1 was replaced with no solution, returning the same defect, so I put a cooler on top of the processor and the result was nothing but the problem. | Defective pci card but it was mine and it was perfect until today, ok, sound's the solution for anyone who has one of these, ok, good luck and good service to everyone | eletronica publison natal rgn |
| SAMSUNG |
UN40J5200
|
Only the standby flashed, the LEDs did not activate after disconnecting the main power cable. | Faulty main transformer | Main transformer replacement | Arnoltec |
| SAMSUNG |
PL43F4900AGXZD
|
Dull(weak) image with pigmentation | R4063, open smd resistor on the power supply board, x main circuit. | CARRIJO | |
| SAMSUNG |
LN26A330
|
White image | Power supply at vcom was low, 6v | As I didn't have the schematic for this board, I isolated the power supply paths from the flat that goes to the TCOM, soldered a wire to the VCOM fuse (screen board) and removed 12V directly from the power supply. it worked perfect. | TECNARDI |
| SAMSUNG 4K |
UN49NU7100
|
Image only in the middle of the screen. like a strip of light in the middle of the screen with a normal image and the sides, everything is dark! | Burned out led bars. | Replace the LED bars for identical ones. replace resistors r9201 and 9101 with this value (4r7 x 2w). Replace or sand the light diffuser acrylic as this TV model burns out the LED and also the acrylic. | EvandoViana |