☰

Samsung Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: samsung
Results: 3800
Make Model Symptom Problem Solution By
SAMSUNG LT24A550
BN41-01594B 		Turns on normal image comes on after a while the digital signal disappears and the information appears free signal or option not available Ic-705 close voltage regulator or varicap varying the output voltage Bynhoteck
SAMSUNG UN40ES6500G
LTJ400HV05G 		It turned off and no longer turned on a short signal at the power cable input Doesn't start Jose
SAMSUNG PL51E490B1
It only turns on when it wants, and without the 5v stand-by Smd transistor d4186 is in position qm861 next to the 4 photo couplers Replace the same Airton Filgueira
SAMSUNG LN32C530F1M
Does not turn on, red light flashing, stand by flashing. C210 shorted and 9v regulator ic202 SERVITEC Quixadá Ce
SAMSUNG UN40EH5300
Dead power supply, dead tv Cp818 blown, icp801s (spc7011f), zdp801 (in front of ic icp801s (double smd diode)), fuse at input fp801s Replace of the mentioned components Claudio Jorge Eckert Junior
SAMSUNG UN65RU7100
Does not turn on or standby Capacitor cp818 toast and qp802 shorted Cleaning the board because the capacitor carbonized, changing the transistor, in my case I put two w20nm60 same rds on and voltage, but with higher current, and cp818, 221k for 2kv and 5a fuse the board started working again Mitzko eletrônica
SAMSUNG QN55Q7FNAG
Only standby, when pressing power it did nothing and turned to standby After analyzing the TV boards and finding nothing wrong, I decided to open the one conect for analysis and located a heating in the middle of the board. When measuring, I found a shorted capacitor next to IC207, I removed the c267 capacitor and measured it outside, finding a short. When turning on the TV without it, everything worked perfectly. Eletrônica Mirage
SAMSUNG UN55MU6400G
FA01 		Doesn't start Correction of the tip to use an alternative board from the 49mu6100. You also need to change the WiFi module and use it via remote control, as the mu6400 button is the only one André
SAMSUNG UN55MU6400G
FA01 		Doesn't start Main pci bn94-11955g very expensive and hard to find. I put one from 49mu6100 bn94-12439g and it worked perfectly. alternative for the original plate. Replacing the main PCI with the alternative André
SAMSUNG UN46FH5303G
Does not turn on, no standby Fuse fp801s open, transistor qm801cs shorted and ci pwm 3s111 defective, replace them all. NiloTech
SAMSUNG HT-F505/ZD
Device turning off (fan ng message on panel) Oxidized cooler connector, replacing it solved the problem juan
SAMSUNG UN40ES6500
When switching on, the relay hits and nothing else, without 13v and 140v power supply voltages. LEDs, with low pulses at these voltage points. In this case the problem was 01 of the 4 Q9401 MOSFETs shorted, just change it and the problem was solved. ALBERI F S
SAMSUNG LN32C45E1MXZD
Turns off and on by itself I don't know Luis
SAMSUNG UN40H5103AG
UN40H5103AG 		Inoperative without standby Short identified in capacitor cz2016 on the main board and capacitor c1 on the joystick board After replacing the two capacitors, the TV returned to normal operation. Leotr
SAMSUNG UN46F6400
Stand by LED blinking and does not turn on, power supply does not double voltage Missing 13volts in qs801 Ds 806 in power supply, open LABOTRON
SAMSUNG LN40C530F1M
BN44 00340A 		Backlight turns on and off or flashing, power supply buzzing Power supply Replace the fet qp802s, diode dp804 and if it continues flashing and the power supply continues to make noise, replace the 2 capacitors of +b cp803s and cp804s RafaelSena
SAMSUNG 39EH5003GXZD
BN4400496A 		Standby LED blinking and when disconnecting the cable from the main backlight it blinks. Can use diode dm804,dm805 or photo coupler pc801s In this case, the PC801s was replaced Nando Cell
SAMSUNG LT23D310
With sound without image TV outputs audio normally, but no image. the defect was on the power supply board wsound the third pin of the connector was completely oxidized and tsound was no more soldering littlecarlos
SAMSUNG UN55TU8000/7000
Decrease the current of the LEDs LEDs burn out In the 2 resistors located next to the socket that powers the panel, add a 1r resistor to each of them in series, thus increasing the resistance and decreasing the voltage to 3v Cj Sgarbi
SAMSUNG PL42B450B1XZD
Distorted image after replacing the main PCI Panel configuration in service mode. In my case I replaced the type option to 42hspb3d and then reset it in the factory reset option in service mode George Lucas