Sharp Repair Tips
Search: sharp
Results: 1789
Results: 1789
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SHARP |
5BSA 51AT15H
|
Small pic - ht low (should be 108v) | Check d716 27v & d717 75v zeners by replacement | ||
| SHARP |
5BSA 51AT15H
|
Slow start, cogging, loptr failure or tripping | Replace all 6 elects on psu sec & q704/708 bc338-40 5v reg trs & q601 bu508dfi loptr | ||
| SHARP |
5BSA 51AT15H
|
Short pic & no reponse to front or r/c | Q509 bc635, q510 bc338 next to field o/p pair & c713 100µ 16v | ||
| SHARP |
5BSA 51AT15H
|
Powers up from mains switch, led flashes then goes out with no pidc or sound. when switched off high pitched noise comes from speaker going down in frequency | Dj on d710 and c713 1000uf 25v s/c | ||
| SHARP |
5BSA 51AT15H
|
Picture jumping | Replace c209 and c808 cap*100nf20v, cap*47nf20v | ||
| SHARP |
5BSA 51AT15H
|
Pic jumping | Replace c209 100nf 20v and c808 47nf 20v | ||
| SHARP |
5BSA 51AT15H
|
Not stopping in tuning, pic distorted | Corrupted eeprom, enter service mode and set aft to 9f | ||
| SHARP |
5BSA 51AT15H
|
No teletext | Ic1001 sda5254 (rhix1578bmn1) | ||
| SHARP |
5BSA 51AT15H
|
No sound/pic & all o/p volts a third down | Q509/510 in fop s/c | ||
| SHARP |
5BSA 51AT15H
|
No sound/pic - goes to st/by aft 30 secs | C604/c622 220µ in line dr cct (not c804/822) | ||
| SHARP |
5BSA 51AT15H
|
No green | Enter service mode (v-, p+ & mains on) to check setting - was set to zero | ||
| SHARP |
5BSA 51AT15H
|
Loptr runs hot and goes s/c | Replace q602 rhtx0118bmzz (loptr q601 part no rhtx0132bmzz) | ||
| SHARP |
5BSA 51AT15H
|
Lines/chopper tfmr sqealing | C804 & c822 220µ in line driver stage | ||
| SHARP |
5BSA 51AT15H
|
Led pulsing, lack of frame. intermittent | C713 1000uf leaky and q509 (rhtx0108bmzz) leaky b/c | ||
| SHARP |
5BSA 51AT15H
|
Lack of height with pattern on screen | Replace c713 1000mfd | ||
| SHARP |
5BSA 51AT15H
|
Lack of height and patterning on the screen | C713 1000uf | ||
| SHARP |
5BSA 51AT15H
|
Int off with screeching causing corruption of agc & afc memory settings | Q708 bc338-40 in sw5v - used bd131 as higher powered replacement | ||
| SHARP |
5BSA 51AT15H
|
Int loss sound and/or colour for 1sec . | Change c209 from 1uf to 100nf 50v pt no vceaga1hw104m , c808 from 100nf to 47nf 50v pt no vckytv1hb473k ( use only sharp part | ||
| SHARP |
5BSA 51AT15H
|
Int cuts out | Ht ok, 5volt supply +5vb low q708 bc338-40 u/s | ||
| SHARP |
5BSA 51AT15H
|
Ht high at 114v (105v) & eht varying (can blow bu508dfi (don't fit bu508df) | Zd717 & 718, q708 (7v supply) faulty |