Toshiba Repair Tips
Search: toshiba
Results: 5591
Results: 5591
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
TOSHIBA |
LC4246FDA
|
Green LED is on and won't turn on | N807 3.3 volt regulator changed | Remove and install a 3.3volt regulator | antonio nobrega patos pb |
TOSHIBA |
1454
SK11 |
Sometimes no audio or snoring audio | C603 470uf 25v in 12v supply | Replace c603 | beto2828 |
SEMP TOSHIBA |
2981
LEM7 |
Bad kinescope board connector | Dark image | Wanderson | |
TOSHIBA |
TV2959JFS
|
Does not turn on, LED is off and power supply is dead. | Defect in the power button. Be careful, as the primary power supply has tension even with a defect in this button, but the pulse to the oscillator is missing through r874. you are | PVB | |
TOSHIBA |
42XV500DA
|
Doesn't start. relay clicks as if it were going to turn on | C893 22uf/50v, c8490 1uf/50v,c815 1uf/50v, c845 22uf/50v, c898 1uf/50v, c884 22uf/50v,c862 2,2uf/50v | All these capacitors were dry (zero capacitance) all replaced and the TV was normal. | Patriarca |
TOSHIBA |
TV 2177 SL
SL11 |
Does not turn on, LED does not light up | R 874 Asaq crossed | I replaced r 874 of 39k and also c 819 10mf 50v as per advice from other colleagues. | Ismael |
SEMP TOSHIBA |
TV2157BFS
|
In stanby, normal power supply, does not turn on | R437 from 2k7 open | To replace | Dj Velk |
SEMP TOSHIBA |
TV1030 TV1431 TV1415 TV1451 TV2015 TV2016 TV2016 TV2051 TV2086 TV2157 TV2158 U18
U18 |
Noise at the power supply killing the voltages (all) | Q865 | Replace | Alextecnico |
SEMP TOSHIBA |
32XV600DA
|
Turns on normally and after a few seconds the back light lamps turn off | The defect occurs because the controller does not receive the pulse related to the inverter board and activates the protection, the sound remains normal | Check if tsound is 24 volts on the inverter board if it is ok replace r24 and r29, c1,c2,c3 in my case it solved | Denilsonti75(epinfor) |
TOSHIBA |
MS7980MUS
|
Firmware update when tsound is no audio | Http://upload.tecnicenter.org/download.php?file=00390c1e663081610924ff2012025d06 | Download update from this link and update | beto2828 |
SEMP TOSHIBA |
1451NAV U18
|
Does not turn on. red led on | Capacitor c884 open. Broken terminal inside. | REPLACEMENT OF COMPONENTS | BICHARA |
TOSHIBA |
TV2958HFS
FS6 |
Turned on, the name Toshiba appeared and turned off | Qb20 smd proxima do ci vertical | In my case it was just cold welding, but it could happen if it was open | ELETRÔNICA CAVALCANTE MARTINÓPOLE-CE |
TOSHIBA |
14"
U15 |
Turns on with dark screen without image without sound without characters when the screen increases, the displey opens with return lines | R413 - 3k9 | Just replace and get the farmiria. | Eletrotião |
SEMPTOSHIBA |
XB4351MP
|
Very low sound comes out | Lack of -12v | Replace resistor r46 valor 410r 2w | JORGE TV TÉC PARANÁ |
TOSHIBA |
MC-855MUS
|
Not reading cd | I bought a soh-ad5 head unit from an electronics store, I unlocked the soldering ball, it didn't read the CD, I replaced it in the store, this second lens didn't read it, I thought it was incredible, I searched for an original one on the free market with the complete mechanism, I unlocked it, I put the CD in, it read it, Look at the difference, this type of device only accepts the original unit | Resolved | Andrei |
SEMP TOSHIBA |
DL4045I
|
Does not turn on or light up on standby | 3.3volt power supply defect | Replace c.i. n805 3.3 volt regulator near the micro heatsink | eletronica fernandes(to) |
SEMP TOSHIBA |
32L2400
|
Doesn't start | Ci nw907 | Replace | Marcus Pacheco |
TOSHIBA |
U16
U16 |
No characters | Ic501 microm | Replacement | BIRA |
TOSHIBA |
TV 2988MMS
LEM9 |
TV doesn't turn on led blinking straight away killing the tension of the sound output funny that when you release the output it returns to normal leaving the impression that I had a shorted output I even had to change it but it didn't solve it | C631 blue polyester 1v7, 1k63 | ELETRÔNICA MUNIZ | |
SEMP TOSHIBA |
40L2400
|
TV won't turn on stand by LED off | Tsound were all initial voltages except 3.3v on the n805, the output was 0.8v | Replace do ic n805 | Paulo Pinho |