Toshiba Repair Tips

Search: toshiba
Results: 5617

Make	Model	Symptom	Problem	Solution	By
TOSHIBA	TV 2157	Does not act contrast	Resistor r226 (3k5) aberto		This email address is being protected from spambots. You need JavaScript enabled to view it. (Bruno)
TOSHIBA	TV 2999	TV with dark band in the shape of a curve on the left and right of the horizontal	Change the transistor qd 01		multsom
TOSHIBA	TV-2958GFS	Red dashed line in the center of the screen	Without an image, only a red horizontal line formed by dashes appears in the center of the screen. cold solder was found in q301 and q830 and the problem was resolved.		littlecarlos
TOSHIBA	2090 U15	Gray screen without characters	D 840 zener of 5v6 I curto	I replaced the 5v6 zener that stabilizes the base of the q 840 which in turn feeds the 5 voltages on pin 9 of the micro	This email address is being protected from spambots. You need JavaScript enabled to view it.
TOSHIBA	TV2998ASU	Turning off and or sometimes it doesn't turn on	Leaky zener diode d818	Replacing the zener diode d818, working ok	LIDERELETRONICA2009
TOSHIBA	TV2134	No contrast	C329 sold out	Replace the same	DANIEL SOLÂNEA PB
TOSHIBA	TV1491KAV U15	Doesn't start	Bu 808 dfi short replace c 419 exhausted	In place of the bu 808 dfi put 2sd2499 works without getting hot	ELETRONICA MAURI JUNIOR
SEMP TOSHIBA	1488IM U15	White screen without characters	Broken eeprom	I replaced and re-recorded the eeprom with the 1490 file. Note: the 1490 file I recorded on an eeprom from the 20-inch CCE TV and it worked because you need to have at least 4096 kbs in the eeprom	leiroz
TOSHIBA	TV2090	Bands on both sides of the screen and a very clear stripe in the middle wanting to double the image,	About the bands on the sides, it was the c884: 220x160volts, without capacity in the +b line of 113 volts and about the list wanting to fold the image in the middle, it was the c306 of 1000x16volts in the vertical circuit, already well inflated.	C884:220x160volts and c306:1000x16volts were replaced and the TV was ok.....	Armando de OLímpia
TOSHIBA	TV 2084GAV U12	Does not memorize channels in auto selection, only manual.	Change aft coil		DEBIQUE
SEMP TOSHIBA	U13 U14 U15 U17 U13 U14 U15 U17	When the vt heats up it turns off	Replace the vertical outlet 81 86302516		eletronica total andre
SEMP TOSHIBA	U14 U14	The stand-bye LED turns on and then turns off and the power supply turns off	Change the flaybak		eletronica total
TOSHIBA	TV 2998 DS LEM U10	Does not turn on, +b with 75v, overheats q801, trips	D 820 as escape		Lima
TOSHIBA	TV2923	When switching on, the stand-by LED lights up when starting, the LED goes out, giving the impression that it works but the power supply drops to zero or 24 V (protects)	The cause is a high 145v supply or the 220k resistor 851 is altered or open. Remembering that the horizontal output sometimes becomes short-circuited.	Replace 220k r851	WAGGUINHO
TOSHIBA	TV2958FS6 LME8/FS6	TV doesn't turn on with the + b with 165 volts when it turns on the d 883 gets shorted	Lightning, I turned off all the r g in the primary they were all ok, I turned it on and the said d 883 burned, then it was the r 874 with the test it's good	Replace r874 and the photo coupler, and it returned to normal 130 volts.	LUIZTVSOM
TOSHIBA	1484FAV U11	Turns on the stan-by turns on and then goes off and doesn't light up again, only after a long time does it turn on and off again	Check r 876 of 680Ω on pin 1 of the str.	Only replace it if it has been altered or opened.	Eronaldo
TV TOSHIBA	1484FAV U11	Turn on the series light, it makes a horrible noise in the power supply transformer, if you don't unplug it, it burns the str, check r876 on pin 1 of the str.	R 876 was open causing noise in the traffic and even the strf5653 burning		Eronaldo
TOSHIBA	2079FMS U11	Tv with normal sound blue screen without characters with lines	Higdg	Dfdf	fabiano
TOSHIBA	TV1452 -O U19	When turning on the panel, it reduces and turns off, the LED blinks	C865 disc capacitor with leakage		Domingos da Eletronica
TOSHIBA	TV2090 U14	Does not turn on, stand by LED is on. +b low (80v)	C887	Replace c887 (100μF 35v) for a 470μF 35v one at the +or-20v output on the power supply's secondary.	Manoel (Noca)