Repair Tips
Search:
Results: 87708
Results: 87708
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
32PFL3404
|
It turns on the sound, the video is loud, and the screen is bright, but then it turns off. | Support for two LCD lamps loose. | I resolved the two and reinforced the others. | Ademir tc |
| SAMSUNG |
PL43F4000
|
Turns on has sound and video, but turns off. | Welds with poor contact and especially in cs809s, redo the welds at the power supply. | Ademir tc | |
| CONTROLE PS4 |
CONTROLE PS4 JDM-055
JDM-055 |
Ps4 jdm-055 control diagram | Jdm-055 | external link... | NEUPSX4 |
| SAMSUNG |
QN50Q60
|
Blue screen, restarting | The defect was in the v-com on the right side, I isolated some tracks of the flat that made the connection between the plates and the image returned to normal | ||
| BRASTEMP |
BMT45
|
Operating the keyboard alone | Remove the acrylic from the panel with a wrench on the sides, wash the board and then resolder all the components one by one until the circuit is integrated | reginaldo moronte, eletronica junior caldas novas | |
| PHILCO |
PH39N91DSGW
|
LEDs light up but weak, image dark | Capacitor cw908 and cw922 100/63v swollen, located next to the transformer | Replacing capacitors | ELETRONICA KLEIN |
| SAMSUNG |
UN40J5200
BN41-02307 |
TV won't turn on main board | Replacement of the synchronous voltage regulator ic206 and the open fuse f202 on the main board | Replace regulator and fuse | marcos moreira |
| AOC |
LE50D1440/20
|
I'm sound | Remove it, leave it without it, or replace the transistor q6002 | Tiago eletrônica | |
| SEMP |
32S5300
|
Does not turn on, voltages are all ok | Open 220Ω resistor rdc5, located next to udc1 | Replace of the same | LEANDRO VOSS |
| SAMSUNG |
UN40J5200
L40MSF_FHS |
TV doesn't turn on | Change mosfet qm803, dm855c and dm861c the same, it's shorted | Replace the mosfet and diodes | marcos moreira |
| STI |
LE2456
|
Doesn't start | Ci smd fr9889 | Replace ci fr9889 in position n804 next to the display connector | Brackmann |
| RADIO CD AUDAX |
AX-2013
|
Alloy has sound, but low sound | Depleted capacitors close to the amplifier | All radios were replaced ok | Fernando técnico rj |
| TOSHIBA |
39L2300
|
The TV turns on immediately, the panel blinks, the lighting increases, but tsound is no image or sound. | Main board defect. | Altered capacitors in the converter, c9059, 9060, 9061, 962, with leakage or low resistance, replace them all. | RNSPTEC |
| LG |
14FK3RB
|
Does not come out of standby, 91k resistors ok, I measured the 5 volts on the ic803, I measured the ic806, it did not release the 9 volts, due to the micro not releasing tension on pin 29, I soldered a 10k resistor on pin 4 to pin 1 of the ic 806 TV turned on but with the image distorting, I concluded that it was one of the crystals | O cristal x502(32.768 | I replaced the x502 crystal (32.768) and removed the resistor that I placed on the ic806 and the TV was ok | DTEC-ELETRONICA-Massapê-ce |
| PHILCO |
PH42F10DSGWAC
|
Does not turn on / only the standby access. | Shorted vw9 or vw10 diode | Replace shorted diodes // felipe reletros | TAVARES |
| LG |
21FJ8RL
EAX5773090614 |
After about 10 minutes on, the image started to shake and tsound was a cricket-like noise in the transformer. | After testing everything, the defect was the broken strw 6554a | Jr eletrônica | |
| H61 |
BIOS PLACA MãE INTEL H61 [G578F34-2]
BIOS PLACA MãE INTEL H61 [G578F34-2] |
Bios motherboard intel h61 [g578f34-2] | Ḍḍ1 | external link... | NEUPSX4 |
| BUSTER |
HBTV-32D01HD
BUSTER HBTV |
Dados eeprom buster hbtv-32d01hd | Dados eeprom buster hbtv-32d01hd | external link... | NEUPSX4 |
| KNUP |
KP-W014+
|
Xbox parallel power supply won't turn on | Ci smd oscillator ob2269cp | Replaced the pwm ci of the power supply, the red led turned on | lucafer |
| PHILIPS |
32PFL5604 32PFL3404
|
Does not turn on, the stand-by LED lights up and flashes quickly, but the relay does not hit, it does not accept commands via remote or keyboard | Power supply defect, 2r2 smd resistor position rb3, on the power supply primary, underside of the board, resistor changed to 15k, is close to the chopper transformer of the 3v3 power supply of the i.c3 fsq510 | Replace rb3 | MIGUELTV |