Repair Tips
Search:
Results: 87709
Results: 87709
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| AOC |
32S5195
|
TV without sound after changing and display | When changing the ID panel in the service menu it may be left without switching between the 7 available displays of 32 to choose from until you find one that suits the image and works the sound | william joner viamão rs | |
| LG |
32LH510B
|
Standby light on but not turning on | Ic 500 short | eletrônica newtec | |
| SAMSUNG |
UN65NU7100
|
TV heats up and only the sound disappears | Speaker with the coil scraping and activates the sound amplifier protection. defect caused by using sound at maximum volume. | Replace speakers | SANTOMEL |
| LG |
43UH6100
|
Image appears and turns off in a direct loop. | Low power supply. When turning off the LEDs, the TV remains on but with the power supply at 160 volts | C612 shorted | LABOTRON |
| PHILIPS |
70PUG6774/78
|
Duplicate image after changing the board to another model | Transfer the U409 EPROM from the original board to the new board! Right tip from Leandro Sena | Tip passed on by rodrigo cofferi | Rodrigo cofferi |
| SAMSUNG |
UN32EH5000G
|
Stand by LED flashes 5 times but does not turn on | Cold solder on the processor | 2 minutes with station 850 did the trick. lol... _good luck! | Jhone eletronica |
| SAMSUNG |
UN32EH4000G
|
Power supplys ok but not on standby led off | Ci 202 shorted or leaking | Replaced sleep.... good luck! | Jhone eletronica |
| SONY |
KD-55X705G
|
Washed canvas | Main board | Reballing the processor or changing the main one. heating the processor at 400g flow 6 the image will come back, but will stop then, solution for testing. | Wallace |
| LG |
50PA4500
|
Burning q404 q403q402q401 due to changed vsc voltage | Cause r266 open check all line resistors | reginaldo. | |
| PHILIPS |
40PFL3605 40PFL3606
|
Tv parada, sem 3v3 stand-by | D301 shorted. sb140 diode replacement | Antero | |
| SAMSUNG |
UN50TU8000G
|
LED bus does not light | LED control sector photocoupler, change without testing | HAHNRAHN | |
| AOC |
LE32D3330
|
Does not turn on, only 5v voltage coming out of the power supply | U501 shorted | U501 replacement | TAVARES |
| CCE |
HPS-2198AV
|
Totally off | Short in the tsh area but it wasn't tsh but d807 | Replace d807 burned or shorted | Rogério TV |
| SONY |
KDL-46EX605
|
When turning on the LED, it lights up green and the faint Sony logo appears and turns off and the LED turns red and flashes 6 times | Open fusistor on the power supply pci on the bottom side it is in the upper right corner its value was not visible but a 0.5Ω one works well | Replace | Ferraz |
| SONY |
KDL-46EX605
|
When turned on LED go green, Sony logo appears smooth and turned off, LED turns red and flashes 6 times. | Open smd fusistor on the power supply pci I put a 0.5Ω one and it worked great it is in the top right corner of the power supply board | Ferraz | |
| CCE |
C24
|
Does not turn on, stand by LED is orange instead of lighting red and then green when turned on. | Diode d11 in4007 change without testing and go for a hug. | ALBERI F S | |
| LG |
21FU6TL
CW62E |
Vertical closed with lack of synchronization in characters | R311 =30k open | The solution is to replace it | ELETRONICA EM CAEM |
| PHILCO |
PH16D10
|
12v input with short | C902 | Edtec | |
| PHILCO |
PH55M LED SMART 3D
|
Does not turn on standby LED on | Measure the power supplies in my case it had 3v3 standby, 24v and 2v4 poweron, it was stuck on that, on the main board it only had voltage of 1v5 and 3v3 | On the signal board the dc dc converter responsible for the 12v was defective they would be u206 and q200, after that all voltages returned to normal except the 1v1 voltage and the dc dc converter responsible for this voltage was also bad which is composed of u205 and u207 | Ariel Santos |
| PHILIPS |
32PFL3404
|
Turns on with normal power supplys with inverter fault, lamps off | Ch1/ch2 | Replace the ch1/ch2 ceramic capacitor 1k | Medeiros Barbacena MG |