Repair Tips
Search:
Results: 88103
Results: 88103
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
TFP2130
|
TV turns on normally with a beautiful image, but the image has a flash or lightning in the image and very thin colored lines | C=607 shorten | Replace it with another and run to the hug | Antonio Carlos (Eletrônica Renascer) |
| SONY |
MHC-GTR888
|
Giving protection when using cd | CD mechanism motors with altered resistance or almost shorted | Replace engines. | Luidio |
| STI SEMP |
LE3273
|
The LEDs don't work | It was not taking voltage to the gate of the fet q412 | Open 1m resistor r418 that takes vsen power on the ic ic400 | josecarlossds |
| PHILCO |
PH42M61
|
Call and "wait", sometimes it works, sometimes it doesn't. does not tune channels. sends hdmi inputs, for example, tv turns off. doing wrong functions. | Change the ci that generates a voltage of 3.3 v, close to the channel selector. | Replace 1117-33 | arock |
| AMPLIMATIC |
ET5000 SLIM
|
Low, buzzing sound, buzzing. | C44 defective | Cap 22μF next to the audio ci | fabiusmax |
| ACER |
P5WE6 LA-7092P
5250 E VARIANTES |
Notebook turns on and doesn't show video (without 1.5v and 0.75v) | 1.5v c.i does not release voltage and consequently does not have 0.75v either | Replace the c.i (tps5117) which is close to the usb flat cable connector. | Darci Denzer |
| SEMP |
TV2934
SK91 |
Does not obey control and keyboard | Leaky volume keys | To replace | GDP2 |
| LENOXX |
CA-318
|
Does not load | Replace of primary power supply components | P70, dsht, p13, rch, uch, ush, p32, cs, f1 | MarcaEletrinica |
| LG |
32LT360C
|
Does not turn on or turn on the stand by. | Power supply defect | Substitute f100 + q6001 + q602 | Eletrônica Morais |
| LG |
CM7420
|
Does not turn on standby light on but does not turn on | Display panel micro switches | Replace all micro keys | paze |
| LG |
21FJ8RL
|
Vertical closing | R-311 (30k/0,25w) | Replace the r311de 30k eli is open! Note, measure the resistor outside the board because if you measure it while it is on the board, the resistor is fine, but it is failing. | Sinailson furtado |
| PHILIPS |
40PFL9605D
|
Turns on and off LED flashes 9 times check voltage of 15 volts if it is normal on the tcom board if it is defective and the voltage does not change. on the input and not even on the ci fet 1102 fds 9435 resolders the bga. | Bga gets cold solder over time due to heating ic301 | A reflow was performed on the bga ic 301 with flow and temperature between 320 and 350 degrees for 3 minutes. Wait for the plate to cool, clean it, remove excess flux, assemble and turn on. go for the hug | Adriano Miranda |
| SEMP |
LC4241W
|
Relay starts but doesn't turn on | 22/50 capacitor close to c 841 on the side. | Tec center | |
| SAMSUNG |
UN40EH5300G
|
No image, backlight on | C24 smd na placa tcom | Eletrônica Cecé. Brumadinho MG | |
| SANYO |
CTP 6792
|
The normal image appears, but with a blue bar running downwards dividing the screen in the middle. | Ic271 | Replace the IC271 LC89950 and the TV will work normally. God be praised! | Sinailson furtado |
| STI |
MLC1560W
|
Doesn't start | Ic1 - code .63831 smd = ob2263mp com fuga e capacitor c6 - 33uf 450v tufado e r9-100k 2w aberto | I replaced it, monitor is ok | Andrei |
| PHILIPS |
42PFL3604
|
Does not come out of standby | C 474 on main board | Miratec Eletrônica | |
| SONY |
MHC-GTR88
|
Turn on and off | Burnt exit | Mauro | |
| PANASONIC |
SA-AK36
|
3.3v voltage oscillating between 1 volts is 3.3 volts | Diode d10 on the FR103 power supply board | Replace d10 diode | josé everaldo dos santos ribeiro |
| AOC |
L42H831
|
LCD panel lamps flickering, flashing, shaking, varying | Q906 e zener 15v zd901 | The 12v and 24v voltages are unstable... varying | Reginaldo Baldoino |