Search:
Results: 88106
Make Model Symptom Problem Solution By
SAMSUNG LT27A550
No audio when the volume increases, the headphone appears as if the plug had been connected. Change the headphone connector because it is dented or repair it. Changing the connector and solved the problem ELETRONICA OURICURI
PHILIPS 42PFL3604
Time calls time no Change the capacitor c474 on the main and c806 power supply speedtec
SAMSUNG CL21K40MQ
When increasing the volume the image shakes Change the 100/160 and 47/160 capacitors on the +b line
CCE HPS 1403
Normal sound without screen image was not working. Swapped flyback tat1409c fabio torres
SONY GRX800
No audio Defect in the fan caused the audio solder in the STK to overheat Resolder the stk and replace the fan
PHILIPS 42PFL3604
When trying to turn it on, it hits the relay, but it doesn't hold. Power supply defect, tsound is a case that is the main board, but this case was knocking the relay and not holding the relay. Replace fet q803, 6n65, if you measure on the x1 scale you will see that tsound is a passage between the drain gate and it did not switch by doing the switching test with the multimeter. MIGUELTV
PHILCO PB 126L
Nao and usb Measuring 5v from usb was not available. I changed the USB touch key and it worked.. Just replace the USB touch key and the same as the Pley Eduardo Callai
SAMSUNG CL29Z30MQ
Generates and cuts, oscillates and cuts or when it is in standby, press the power button and the LED turns off. R821 changed or opened Just replace it and run for the hug. leilson lagoa de roça
AOC 32D1352
No image on the channels but with normal sound, with normal sound and image on the audio and video via rca Corrupt eprom data in the service menu put values ​​of 128 in the compensation and gain rgb claudio
LG 21FS4RLG
With all voltages with sound but no image Defect in the tube killing the screen voltage Remove the solder from the screen pin on the tube and increase the screen to maximum and with the TV on, touch the screen cable several times to the pin you released until the image appears Mario Moreci
CCE 2118 USP AV
Vertical closed Check transistor v541, if it is not open. +13v power supply, from the vertical output. and replace the n301 stv8172a for the la78141. These TVs come with vertical aid, stv8172a, but in the schematic, it indicates la78141. the stv8172a, most of which are commercially available, are counterfeit. You have to replace it with la78141. MARCONES DE ARARIPINA PE.
PHILIPS 20PT32678R
The standbay LED turns on and turns off, then the power supply capacitors remain charged, not turning on C2511c2509 47por160v I put the capacitors on the binba TV and it was fine, just fillet Gabriel eletronica
PHILCO PH21B
PH08K-A(VER:0.7)
Vertical closed shutting down Lack of 8 volts on pin 3 of icn301 causes capacitor c312 to short, replace and it worked Luis Aquino sparapan
TOSHIBA TV2159NFS U18
LED blinks continuously In my case it was this c865(103lkz) Replace and resolved vídeo som Escada-PE
ELSYS 2.0 PRETO DUOMAX
Turns on normally, the display lights up, but tsound is no image or sound, the screen remains black on both the RF and AV outputs. Diode d116 open In4007 common diode replacement Heliton
ELECTROLUX MTD-30
When you press the start button it turns on and off Bobina l100 robson
ONEAL OCM 412
At low volume, even with the potentiometer at maximum. After so much brainstorming, I discovered that the defect is on pin 4, of ci4, all 2030 the solder, was tinted, and it was barely noticeable. Resolder the audio output pins. MARCONES DE ARARIPINA PE.
SEMP TV2134CSL
SK911
On and off, Change without measuring the q606, I put the bd135, see the pinout. DJ PITUKA
SEMP 2134(C)SL
Turning it on, turning it off by itself. Replace q606 s8050, e c637 1000nf/16v. MARCONES DE ARARIPINA PE.
SEMP 2134(C)SL
Turning it on, turning it off by itself. Replace q606 s8050, e c636 1000nf/16v. MARCONES DE ARARIPINA PE.