☰

Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search:
Results: 88110
Make Model Symptom Problem Solution By
PHILCO PH21US A1
Secondary voltage varying and LED flashing After a lot of research I found r512 from 6k8 changed to 8k and varying between 9k.7 Replace r512 junior
SEMP TV2134CSL
Japan Fund A Nishida Horizon et al. C303 Replace the 180j capacitor c303 to 400v and the TV will work normally Sinailson furtado
SONY HCD-GTX88
Doesn't play pendrive CD carousel not working You have to fix the CD to get the pendrive EletroClaudio
PHILIPS 42PFL3507D
With sound but without image Capacitor in t-con position (c209) and t-con fuse (f1) Mario Moreci
AOC L19W931
Lamps don't light Even after changing c930 lamps do not light up, add another 1000 x 24v capacitor Put capacitors in parallel...adding 2000 micro farads Maurilio
PHILCO TP20V56
It doesn't turn on, it just stays on, the LED is on When you press the switch, the LED flashes, the voltage does not arm and drops, the vertical stv9302a is defective, I replaced it and the electrolytic capacitor with its capacity depleted c918 and c914 - 1000ud 16v Defect resolved Andre
LG 60PB6500
Turns on and then turns off Power supply vs high 240v Open coupler photo. ic503 Eletro Center
SEMP 1454(P)SL
V2.1 		Just standby+hits the relay and doesn't turn on, with heating on r420 Memory with corrupted data, just change it and run to the hug Replace ic n201 (k24co8c) leilson lagoa de roça
SAMSUNG PL51D490
Doesn't work I checked the following components; q 5009, q 5002, q 5019, d5010, on ysus, and on zsus q4002. all shorted. After changing them I noticed several bad soldering points on the zsus board. These points probably burned the aforementioned components. Replace the aforementioned components and resolder the z sus and ysus boards. arock
PANASONIC TC-L42U30B
The LED flashes 14 times and does not turn on Fuse pa850 smd (on the power supply board next to the connector that goes to the main board) capacitor c8780 Eliminate the capacitor (it is on the main board, next to the connector that goes to the display tsound are 4 capacitors, one of them) Eletronicaaeb
CCE HPS-2071
Alloy with lines of retraces is a far image Fr901 Replace the fr901 on the rgb board Sinailson furtado
PHILIPS 220TS2L
When I activate power, it turns on standby and then goes out. Cause: c910 1000µf/10v on the power supply board, near the output harness Lucas
SEMP TV2134CSL
Does not turn on, secondary +b power supply is completely dead, only charges the input cap. Change ceramic capacitor c608 and run to the hug. DJ PITUKA
LG 32LJ600B
LJ7 		It doesn't turn on, the LED doesn't light up, the internal 3.3v power supply pulses, appears and disappears. Capacitor in parallel with the zener diode on the wifi board Shorted capacitor on the wifi board, in parallel with the smd zener diode close to the connector MIGUELTV
PANASONIC TC 32DS600B
Vertical shaking, shaking image Display defect Remove the smd resistors r203, r205 and r206 Dj Velk
SEMP TV2090
U14 		The standby LED does not turn on when the power supply voltage is low at 75v or +b and 20v with around 10v C807 100x35v low and also look at the c419de 47x50v a little low and always good, replace the c419 Replace it and that's it orlando lott
LG 14FK3RB
It didn't turn on, I wanted it to start but the LED didn't even light up. Cold soldering Just replace q402 js eletronica
PHILCO PH32E63D
I'm sound Software Sw update (update menu password 0812) Brackmann (51)997366096
CCE D32
Performs functions alone. For example, decrease and increase the volume, enter the menu, select inputs, among others. Problem with the side buttons. Replace all buttons. Henrique
AOC LE26W154
The first time it turns on normally, if it turns off both the control and the keys it no longer works 3volt power supply Replace regulator g1084-33 you can use az1084-33 which are 3.3 volts 5 amps eletronica fernandes - to