Repair Tips
Search:
Results: 88148
Results: 88148
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| LG |
32PQ30R
|
Colorful drizzle on top of the image even on HDMI. | 2r2 2w aberto na y-sus resistor. | pardal1967 | |
| SEMP |
PL4240
|
Replace c16 | C16 100mf x 16v on signal board | Replace c16 | LUCIANO POLYTROM |
| LG |
21FU4RLG
|
Loud noises in the speakers | Normal | Reginaldo | |
| TOSHIBA |
TV2977(A) SL
|
Image warping and oscillating to the sides and when it heats up it becomes normal | C 889 2200/35v malfunctioning. change it. | After the replacement it was normal. | <small> |
| PHILIPS |
32PFL4007
|
It doesn't turn on, the power supply has 4.7v. | Reg. u702 3v3. replace. | Joaomvjr | |
| SEMP |
TV2982 MAVS
LEM9 |
Cushion effect | Dd06 (her306) | ||
| ELECTROLUX |
MEF28
|
Does all the functions but does not turn on the magnetron, the lamp or the fan | Damaged 100nf smd c11 capacitor, located next to the computer leg | Replace the same, | Eletrônica Reis |
| PHILIPS |
32PFL3404
|
Does not come out of standby | Removing the power supply connector in socket p22 on the main board or on the power supply and replacing it again with the power cable connected, then it works, serves the control and everything else. If you remove the socket from the mains, you return to the same problem and do not respond to any command. | Capacitor c474 de 4,7mf/16v | Helio Eletrônica |
| PHILIPS |
32PFL3404/78
|
Does not come out of standby either via the controller or the keyboard | Removing the power supply connector in socket p22 on the main board or on the power supply and replacing it again with the power cable connected, then it works, serves the control and everything else. If you remove the socket from the mains, you return to the same problem, nothing else matters. | Helio Eletronica | |
| CENTURY |
NANOBOX
|
With audio no image black screen all functions work | Change micro. | Replace micro. | samuel leite |
| SEMP |
TV2134(C)SL
SK11 |
Vertical closed | C725 100ufx16v killing the 8v voltage of the micro ic201 | I replaced it with a new one and it worked normally again. | Emanuel |
| H-BUSTER |
HBTV-42L05FD
|
TV does not turn on after being on standby for some time. If you unplug it and turn it back on, the TV turns on, but when you turn it off using the control and leave it on standby for some time, the TV doesn't turn on again. | Altered electrolytic capacitors on the main board. | Replace all electrolytic capacitors on the main board worth 100x16v. Several of them vary in capacity, making it necessary to replace them all. | rafaelmoraes99 |
| TOSHIBA LED |
32L1500
|
Inoperative: has all power supplys but does not oscillate (led off) | 1v5 regulator | Position n803 on the board. it was 1v0. I tested it outside the board and it gave 1v5 but when I replaced it, the voltage returned to 1v5 and the TV worked normally | ELETRÔNICA Targino |
| LG |
RP14CB25A
|
Turns on and then turns off and the secondary power supply is zeroed | R816 changed in the schematic says it is 1k but if it is placed the power supply is 95v and has a stripe on the side | The correct one and a 180 resistor becomes zero again 110v power supply ok | Elias tv Natal R|N |
| SONY |
KDL46EX655
|
Stand by flashes 3 times, rj45 cable connected and lightning strike burned router | Ci da lan short (realtek 8201), tip falcon electronics | Replace of the same, | tadeu masson |
| SEMP |
TV2083FAV
U11 |
Vertical closing at the bottom 5cm | C305 sold out | Replace it for another like it | ELETRÔNICA CAVALCANTE |
| SONY |
KLV-40M400A
|
TV turns on and off quickly blinking standby LED 4x | Short in component c4086 | The c4086 was removed and the TV turned on normally | Ivan Junior |
| LG |
21FJ6RB
|
Its defect was characterized by turning on the key, but not responding to the remote control, nor to the keys. everything locked. it worked but after about 2 minutes it went out. No solution found on the internet. changing some covers, photo, regulator near the keyboard, tsound was a shorted key, the replacement was done but it didn't solve the problem, so the sensor was shorted, with the replacement it stopped on, but the memory had to be changed, because it was very hot. So, everything is ok. | Sensor and memory replacement. | <small> |
|
| SEMP |
TV2134 C
|
Closed vertical, scoring short on d612 | C107 shorted. | INTERTEC ELETRONICA | |
| SAMSUNG |
CL21Z43MG
KSCA. AA41 |
Echoing the sides when the brightness of the image was strong | D804 and d805 in primary power supply | Just replace and run for the hug | Bynhoteck |