Repair Tips
Search:
Results: 88182
Results: 88182
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG |
CL21Z43
|
Warping the image | The defect happens because the capacitor cr401s touches the q401 heat decipher which becomes hot, this is normal but it causes the cr401s to lose its capacitance | Cr401s of 183x630= 18nf, being able to put the 22nf in place | Ala Sousa |
| PHILCO |
TP2010
PCI 016 REV-A |
Tv-cheering at the power supply | Capacitor 102 0km shorted next to cap 100uf by 160 | Resolved ok | eletrosom-c-a-g.com.br |
| CCE |
HPS 2076
|
Inoperative with b+ of flay beck pulsing between 60v and 72v standbay led off | Q804 bc 337 altered | Replaced and it worked ok | dj nilton |
| PHILIPS |
20PT120
L7L |
The power LED would flash 5 times and it wouldn't turn on, the LED would stay on | Capacitors 2551-2448 os2 of 47 micro160volts os2 stavão without capacitance | Replace the 2 with 47micro 160 volts | jose avelar |
| PHILIPS |
21PT9467C/78
|
Burning ic 601 | D610 shorted | To replace | rn eletronica fort-ce |
| PHILIPS |
21PT9467C/78
|
Burning ic 601 | D610 shorted | To replace | |
| TOSHIBA |
TV2158NFS
U18 |
Vertical closed, I changed the vertical and it didn't solve it, | The c889 does not have 20 volts, do the following from the c887, make a bridge from the positive to the c889, and the TV will work normally... | eletrõnica digi sound | |
| CCE |
HPS-2991FS
|
Stop - note: no starting voltage on pin 1 of ic 801 (tea 1507p) and consequently taking time to discharge the c 816 (470/385) be careful!!!!! | Cause: ic803 (coupler photo) | Replace it - good luck to forum friends | |
| LG |
29FU6TL
|
Vertical closed | D301-1n4005 | Replace without measuring, | ADRIANO..RIO VERDE MS |
| CCE |
HPS2002
|
No picture, normal sound | Q401 defective | Replace q401 | Eletronica Staub |
| TOSHIBA |
TV2087 F
U11 |
Without image and audio, but with high (opening screen - closed vertical) | Q830 | In this case, just solder | Phatal |
| PHILCO |
29
|
Vertical burning and resistor | Vertical change | Put tda9309 in place 8177f island pin 3 of tda 9309 which is 50v solder 100μF/35v capacitor between pin 3 and 6 with the positive side on pin 6 and invert pins 1 and 7 | giovano eletronica |
| PHILCO |
TP29C21
|
Burning vertical | Change to tda9309 | Put tda9309 in place 8177f cut the 50v track solder 100μF/35v capacitor between pins 3 and 6 with the positive side on pin 6 | marlon favero |
| PANASONIC |
TC-L42U30B
KM-10 |
Does not turn on, 14 blinks on the stand by LED | Without 16v power supply - short on peak line - audio output | Pa-850 on the 16v line open on the power supply board (smd fuse), and on the logic board c-8780 (smd 10μF/25v), short | VipCenter |
| PHILIPS |
29PT5645
|
Turns on the image and turns off | Cold solder rgb tube board | Resolder tube plate | |
| CCE |
HPS2991 FS
|
Weak blinking LED, tic power supply, tic, low voltage, TV won't start. | Replace of q808, direct replace, bd846 (1a) replace of d819 1n4148. | joaomvjr | |
| GRADIENTE |
TF2151
|
Does not turn on or takes a long time to turn on (low 10.2v supply) | C506 and c509 10/50v changed | Replace the two | Phatal |
| PHILCO |
PH21D
|
Folded horizontal | Cause: 8v2 zener diode d407 shorted | klein | |
| LG |
20CB20
023A |
LED blinks, beeps and doesn't turn on (it started turning on when it wanted to). | S826 | Replace and run for the hug. | R-TEC Eletrônica |
| PANASONIC |
TC-29G9L
BR1L |
Turns on and then turns off. goes into protection. It only turns on again if you take it out and plug it into the socket. | D405 (36v zener) with leakage | Replace component | Mau 3000 |