Repair Tips
Search:
Results: 88183
Results: 88183
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| SEMP |
TV2134
SK1 |
Setting up protection | C634 47uf-160v with corroded pin! | CompuHelp | |
| PHILIPS |
42PFL3403/78
|
It doesn't turn on, you only hear the relay when you remove it from the socket. | Two 470/10 c108 and 112 capacitors on the 3.3v line | ||
| CCE |
HPS 1491
|
No colors – normal b/w image | Capacitor c 505 (0.01 µf) with leakage | Replace | Eletrônica_Almiro |
| PHILCO |
TP2052N
|
Doesn't start | Power supply transformer with loose ferrite and open r921 and 923 | Paste trafo and replace resistances for 1r | ELETRONICA MAURI JUNIOR |
| CCE |
TV2991FS
|
With retrace (contrast does not work) | C 421 | krul | |
| PHILIPS |
21PT9467 E 29PT9467
SK4.1L |
Vertical closed | D303 e d304 (byw62) e r309, r310 (0,68) | Replace the two diodes with sk4f1/10 and replace resistors with 1r0 | Ádrian Chapadão do Céu-Go |
| CEE |
HPS1473
|
On off blinking LED | Q802 shorted and c823 220mf 16v | Replace | fofinho |
| PHILCO |
PH21SS
|
Vertical closed at the bottom | -13v missing from the vertical diode with poor contact and 1000/25v capacitor with low capacitance | orlando lott | |
| SONY |
HBD _E280
|
Hdmi board is defective | No vidius | cesar | |
| SEMP |
TV 1483 FAV U11
|
When I turn on the TV it just sizzles without showing an image when I turn it off it triggers a reflection on the screen | Unidentified | ||
| PHILCO |
PCM-2046
|
LED blinks and doesn't turn on | C911 sold out | Replacement | beto |
| PHILIPS |
21PT9467
|
LED lights up, when turned on nothing appears, then it starts to click followed by a flash on the screen. | C315,c316,d303,d304,d305,r309,r310,r318 e fly back. | I replaced everything but the resistor and diode of the negative voltage of the vertical ci burned out. I'm still checking. | Rondinele _Campo Redondo/RN |
| LG |
RP29FA30A
|
Just another good one of course | Ic 901 (tda6109jf) rgb | Just another good one of course | |
| SONY |
HCD-ZUX9
|
Turns on and then goes to stand by | Triggers protection | If something is disconnected or the tape player has loose or out of place straps... every time you turn it on it goes to stand by. | eletronica Callai |
| SONY |
HCD-ZUX9
|
Keyboard doesn't work, just turns on and off and volume | Keys | Reset sony fst-zux9 880w rms sound to reset this device, do the following: a-unplug the power cord from the socket. b-plug the power cord back into the socket. c-press the "on/off" button to turn on the device. d-press the "stop", "enter" and "on/off" keys simultaneously. e-the message "cold reset" will appear on the display. note - this procedure will return the device to factory settings. All adjustments made to the device, such as memorizing stations, setting the clock, etc... will be erased. you will have to do them again. | eletronica Callai |
| CCE |
MCS35
MCS35 |
Turns on everything, tsound is no volume (with audio on the app) | Q503 bc337, dz506=d506 zener de 10volts. | It didn't have 9 volts. | Alextecnico |
| SONY |
HCD-EX8
|
Does not adjust manual volume | 493 and 494 amended | Do not measure replace | paulo-maceio/al |
| SEMP |
TV2999KMS
LEM7 |
LED on, won't turn on | Power supply primaria | C819 22μFx100 volts | cabessaonatal |
| SEMP |
2134
|
Does not turn on, charges the power supply capacitor | R602 | Replace | BETO ELETRONICA ACRELANDIA ACRE |
| SAMSUNG |
21K40MQ
|
Fountain stops ticking, ticking in the chopper | Interconnect the diodes d807 with d813 from secondary and non-primary dz801 10v, dz802 4.3v, dz803 27v 1w, dz805 18v. | joaomvjr |