Cce Repair Tips
Search: cce
Results: 4816
Results: 4816
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| CCE |
HPS1402B
|
It doesn't turn on, only the standby light is on. | This TV only had the standby light on, when pressing the power key the light went off but the TV did not turn on, be careful when testing components, because when measuring the capacitor c812 47uf x 25v on the capacimeter it gave 42.1uf a value that was even close the correct value, but guess what, that capacitor was the villain in the story, just put a new one in and solve the problem. | FERNANDO | |
| CCE |
HPS-2097
* |
Doesn't work and power supply blows fuse | Dz 801 insurto | Your replace of the same value but higher in watts. | wagner |
| CCE |
HPS2971C
|
Image darkened and became mute | After checking that the kinescope filament was lit, I replaced the 4k7 r435 of the abl that was altered, and after checking the flyback I found through the diagram that the coil that goes from pin 9 to pins 1 and 2 was open, I changed them and everything OK. | MRinformática | |
| CCE |
HPS1497
|
Power supply + b 103v low and varying the value | Trafo t 801 | ELETRONICA ROBSON (DEBIQUE) | |
| CCE |
HPS 1407F
|
Ci tl431 r816 113k-obs:replace q802 bc337 nem measure | MARCOS UBATUBA SP | ||
| CCE |
HPS1471
|
Blinking LED does not turn on | Q802 broken even good in the test | Replace for one of the same good luck | Evaldo Eletrônica gomes Uruçui-Pi |
| CCE |
HPS-1402
|
Channels with block user "does not remember password" | Put the TV in standby mode and press the following p.ch button on the control. for 2 seconds), OSD key (one touch), mute key (one touch), sleep key (keep pressed until the TV turns on). obs. unlocks several models | Help yourself leave your tip | ELETRONICA ARNI-LEOBERTO LEAL /SC |
| CCE |
HPS 2030
|
C 852 exhausted, str pin b | franco@tatui | ||
| CCE |
HPS21AVP
|
Blurred image of adjustment in scrim | L 402 remove and place a resistor of one (r) in place | MULTSOM | |
| CCE |
HPS-2071
|
No image normal sound dark screen. filament does not light up | Change the tube | eletroclaudio aguas belas | |
| CCE |
HPS1481
|
Loses flashing color | Replace the two crests 501 503 | julio itaguai | |
| CCE |
HPS
|
When changing channels, sometimes it changes normally if the channels go through, sometimes only channel 0 remains. | Eeprom memory 80021 | Fernando | |
| CCE |
HPS 2997
|
Disarms immediately after being turned on | Capacitor eletrolitico 100x160v | Replace without measuring as it misleads when checking | ARASONIC |
| CCE |
HPS-2081
|
+b very low | Ceramic capacitor c 846 with escape | Replace c 846 | ze nascimento |
| CCE |
HPS2185FS
|
Side stripes width | Capacitor c825 47mf/160v | Very good tip because it seemed wide but it wasn't. | |
| CCE |
HPS-2971N
|
Does not turn on, LED is off | C808 sold out | Manoel | |
| CCE |
HPS 2185 FS
|
Totally inoperative | C 808 22x 50 v just change it and go for the hug | CARLOS AUGUSTO ELETROSILVA CANAVIEIRAS BAHIA | |
| CCE |
HPS-2991FSC
|
TV turns on flickers but then turns off 8817 quanaces guy | In my case it was a lack of 13v that comes out of the flayback that makes the 8v a capacitor c 834 /100.16v exhausted I replaced it blz | Capacitor replaced | marcos melo cascavel ceara |
| CCE |
HPS 2971
|
Doesn't start | Fr 804 open replace also tea 1507 | Resolved | eletronica ideal |
| CCE |
HPS-2071
|
Turn it on, turn it off, start it another time, don't start it | Cold solder on flyback pins | Just resolve it. and good luck | eletroclaudio aguas belas pe |