Cce Repair Tips

Search: cce
Results: 4834

Make	Model	Symptom	Problem	Solution	By
CCE	A650 000000	Hoarse sound	Lack of you n ic301 4558, 308 open it seemed like it was the sound output but it was just r r 308 changer was left filer	Replace r 308 15k	eletronica marcos melo cascavel ce
CCE	HPS-1401 H.	Signals only come in via sky or satellite dish, which appears to be a varicap selector.	Ic-101 =diodo zener de 33v,c/ defeito.	It was replaced and it was ok.	Armando
CCE	TV 2991-FS	The TV works and stops successively	Transistor q802/q804/q805 altered and capacitor c409 defective		Rivaldo Lira
CCE	HPS-2991	TV generates without the deflector and with the deflector it generates and cuts.	R416 of 820r open.		Daniel
CCE	HPS 2780	Dark screen and no channel was tuned...sometimes tsound was distortion in the image.	Ok for 33v, vt ranging, agc, la 7910, q-702; The defect was the VCO t-102 coil going to pins 61 and 62 of the la 7685j. thanksuuuuuuu		Gutt
CCE	HPS 2003	Channels with user lockout and the same "doesn't remember" password	Put the TV in st.by mode and press the following sequence on the cr.: p.ch. key (+ 2 seconds), osd key (one touch), mute key (one touch), sleep key (keep pressed until tv to connect).		ELETRONICA ESTUDIER
CCE	HPS2988	Does not come out of stand-by	TV does not come out of stand-by, it was checked, the high power supply +b 135v is ok, which feeds the fly back but it did not generate it. The FBT was changed and the TV worked but with a half screen from the center upwards, vice versa, the cause was resolved by changing the vertical ci tda8359j. good luck if this tip works		TODDY
CCE	HPS 2901	Upper lines vertically, in the first few minutes then disappear..	Ver c- 424 1000uf x 16v	Replace	MASTER
CCE	HPS1415	It starts with a small band at the bottom of the screen and increases as it heats up.	Capacitor c356=1000 for 16v without capacity.	It was replaced and it was ok.	Armando
CCE	HPS1415	Flat screen, no sound, no image and the channel digits do not light up	Q101 =bc337 defective.	It was replaced and returned to normal.	Armando
CCE	HPS-2971	Dead	Dz801 18v 1/2w
CCE	HPS2990 CXA PRCESA	No video	Regulador 7805 ic 204		tec.jorge video som caldas
CCE	HPS 2997FS	Power supply with 185v when turned on drops to +or- 80v relay knocking	R 816 130k precision resistor		Joacyr
CCE	HPS-2004	When I opened the TV I noticed that the bu was burnt out, I replaced it and when I turned on the TV it didn't take long for the bu to burn again. I was suspicious of everything except the flayback, I even changed the deflection coil but the bu continued to burn.	So that's when I decided to change the flyback.	It didn't burn out, but as a precaution, also replace the horizontal capacitors (772j/1600v.c418, which measures 7.72nonofaraids. and the c416 of 394j/250v, which measures 394nonofaraids.	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS-2004	When the TV is turned on, it burns the resistance (fr402) that feeds the tda9309 vertical output. I was not suspicious of the vertical output because the image was open.	But when removing the output I checked pin 5 to 6 of the vertical output was shorted	I replaced the vertical output and the resistance that feeds it and it was fine	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS-2004	When turned on atv. it had brightness and sound but no image. Only a lot of lines of retraces appeared, you could even increase the screen until the end and nothing happened.	That's when I checked the resistance in the tube socket (FR901, 22Ω, burnt red, red and black)	It was just a touch and go for a hug	This email address is being protected from spambots. You need JavaScript enabled to view it.
CCE	HPS 2781	The image warps only in some channel.	Factory modification.	Put a 68r and 1/4 watt resistor in parallel with r408=270r and that's it...ok.	Armando
CCE	HPS 2971	Vertical line on screen	Replace c 409		DEBIQUE
CCE	HPS1403	When you press power, the LED turns off but takes a while to turn on	Replace q802 e dz 807(bc337 e 8v2)		AdrianChapadão
CCE	HPS-2171FS	I replaced the original flayback (bsc25-0206h) with the one that comes with the tat2104 scheme	I just took out the 47kpf c424 and that was it, the image was normal, but it took a while to turn it on and I realized that the filament was very erased.	I put the 47kpf c424 in its place, I took a turn on the flayback ferrite to increase the voltage of the filament, 3volts, the increaser to 4.5volts, it lit up normally and the TV turned on normally without delay, this is because the flayback was not original, but everything was resolved.	fabiusmax