Philco Repair Tips

Search: philco
Results: 4811

Make	Model	Symptom	Problem
PHILCO	PCS-2976	Turns on and then activates protection	C 730
PHILCO	TP 2054	It squeaks, normal image	C401 and or c401/2
PHILCO	TP 2054	No sound	Capacitor smd c-401 330pf
PHILCO	PC 2043	Does not exit std by	Change r908 de82k open
PHILCO	PC 2039	No Sound	C413 cap.ceramico 10k shorted, location pin 50 of ta8690
PHILCO	PCM 2044	The TV turns on and off continuously	Res. 100k open close to the fly back, or d 303
PHILCO	PCM 2044	Horizontal strip	Solda fria no pino 3 do fly back
PHILCO	PCM 2046	No contrast	C716 100n - r706 10k
PHILCO	TC-14TR1	Sometimes it works, sometimes it doesn't.	Cause c-813 change. for a new one.
PHILCO	20C6	Volume does not increase and the menu does not work.	Change the eprom and program.
PHILCO	TCT-14TR1	Intermittent operation.	C-813 (1 µf 250 v)
PHILCO	TVC-20C2	Unstable vertical	C-410 (0.1 µf)
PHILCO	MOD-TC 14C1U	Symptom is just drizzle and the sound is loud and does not control any function	Cause -r882.330k open is on the memory board along with the tr q.881.
PHILCO	TC-20/29G11 / TC-29A11	Does not turn on, without 9v power.	D602 in all devices submitted to authorized service, replace diode d602 with a jumper. If this diode opens, the device becomes inoperative.
PHILCO	TC-20G7 / TC-21V50B	Queima do stk73907-t	Countermeasure: when replacing the ic801 code. stk73907-t the changes must be made as described below: 1. replace the printed circuit stk. Add thermal paste and attach it firmly to the heatsink. 2. add a 130pf / 3.6m capristor. code. exng131p365 between each ac line with cold ground. solder the capristors underneath the print and glue them with silicone or hot glue. 3. add a 10nf capacitor cod. ecqm4103jzw in parallel with c805. solder the capacitor underneath the print and glue it with silicone or hot glue. 4. Add an insulated wire jumper between point A13 and tuner ground.
PHILCO	TC-29V60 / 33V60	Certain devices present a noise coming from the power supply circuit or the deflection yoke, this in turn can be noticed mainly when the television volume is low, in a silent external environment, it is noticed that the noise increases and decreases depending on the scenes lighter or darker.	Changing the power supply transformers t801 - ets39ag115ac t872 - ets29ak1w9ac 2) changing the deflection yoke this yoke cannot be a normal yoke available in stock, so for this change please contact ddg - 0800 55 9180. for information on the procedure to exchange this part.
PHILCO	TC20C02	Retrace lines, screen with excessive brightness, flay-back focus control does not fully work, screen control cannot darken the screen, it only brightens it, and when you try to darken it using this setting, the screen is all blurred with green. channel indicator characters presenting inverted folding together with the same	Capacitor c519 - 4,7uf/450v aberto (seco)
PHILCO	TODOS OS TV MODELOS QUE UTILIZAM O CHASSI MX3-R	Loss of tune after a few seconds	Procedures: a) access the service mode (note the values of the dacs). select functions b8 (for aft) and b9 (for rf agc) and change the values to the factory average values, b8 - 085 b9 - 040.( * ) b) check capacitors c121, c116, c112 and c111 , pin 27 - ic6001(rf-agc) and capacitors c122 and c127, pin 21 - ic1101(afc input). comments: (*) the values given for b8 and b9 in procedure a) cannot be used as standard values, but as average values as each TV has to be pre-adjusted later (the values serve only as a reference, in cases where the values are completely altered.)
PHILCO	TC-14/20A8 / TC-14/20A9	Three to four retrace lines at the top of the screen. This symptom occurs when the memory (ic1102 - code s- 24c02adp) is changed or when the memory data is changed.	Enter service mode .chq3. and lower the vertical center .vc.
PHILCO	CHASSI BR1L/BR1D -MODELOS TC-20G9 / TC-29A9 / TC-29G9	Problem detecting sap	Include the 820kΩ smd resistor r2212. This component is included on the printed circuit board.