Philco Repair Tips

Search: philco
Results: 4810

Make	Model	Symptom	Problem	Solution	By
PHILCO	PH32B28DSGW	Turns on and off, locked restarts	Corrupt software, update via pendrive	On the philco website, enter the serial number and download the update, if you cannot download it through Chrome, use another browser that will close the window as soon as you click, but the download will be blocked, allow the download then	Mitzko eletronica
PHILCO	PH32E63D	TV inoperative power supply defect	Q201 k3673 with leak replaces with k6465d worked perfect in		Mijail eletrônica alternativa
PHILCO	PH32E63D	TV inoperative power supply defect	Q201 k3673 with leak replaces with k6465d worked perfect in		Mijail eletrônica alternativa
PHILCO	PH32 DTV	With sound and backlight. but no image. without the 12v that powers the t-com	Integrated u11	Just replace it	Paial.eletros
PHILCO	PH32 DTV	The backlight turns on and goes off in 2 seconds	Jp36 open	Just replace it	Paial.eletros
PHILCO	PH39N86DSG	Does not turn on or have stand by, power supplys half full	Change eb106	Run to the hug	M.Tristão
PHILCO	PH40U16DSG	No image, LEDs on black screen	Capacitor shorted on screen board cd6	Capacitor replaced	molina
PHILCO	PH21B PH08K_A. (VER:0,7)	Low power supplys +b giving 60v and very weak standby oscillating	C 523, just change everything solved		Jr eletrônica
PHILCO	PH55E51DSGW	The TV turns on, the LEDs turn on, tsound is no video, it seems like tsound is a defect in the main or display	As I have already obtained several tips on this site as well as on You Tube, I am passing this on to my professional colleagues: first check if tsound is a ci on the tcon with high heating, if so, turn off the flat in my case on the left side of the vcon then see if it has stopped the high heating in the ci, if so go to vcon and see the c107 smd in short it will solve it but it could be others that are on the same line in parallel, hugs.		Digitronica
PHILCO	PTV43E60SN	Beep in the audio after a while when connected and without an internet connection	Defective wifi card	Wifi card replacement	ELETRÔNICA POP TRON MAFRA SC.
PHILCO	PH28S63	Doesn't start. Stand by LED does not light up	Dead power supply	Capacitor c8->221x1kv , transistor q2->4n60, fuzivel f1 ->3,15a	oskarala
PHILCO	PH650	No sound/voltages ok	Headphone output board connector closing as if plug connected	Plate replacement or cleaning with contact cleaner	Renato
PHILCO	PH21MSS	Frame reduced horizontally, more on the left side than on the right	After changing the power supply capacitors and resoldering on the board I found the r306, close to the vertical one, toasted, the value of 220r was replaced, the board was even reduced. I found a L458 coil without the ferrite magnet. was replaced and adjustments were made to the service mode		Mitzko eletronica
PHILCO	TP1454	TV with normal sound and no color	Memory	After a reset the TV was normal	Eliel Magno
PHILCO	PTV32E21DSWN VA	Image upside down after broken screen change.	Original screen t315xw03, replaced by hv320whb from a sony.	This model has several screen models in service mode, but the one I had installed was not on the list. This TV has 3 software versions. if it happens to you. check the lyrics after the series, if the	OLIBIO - ELETRÔNICA ESTUDIER
PHILCO	PH32S61DG LED	Normal power supply, LED does not light	N804 fr9889		Arimateia
PHILCO	PH40D10DSGW	Turns on, philco appears and turns off	3.3v regulator, close to the selector, leaves 2v	Replace of the same	Rodrigo cofferi
PHILCO	PH40U21DSGW	Turns off by itself after 20 seconds on. goes to standby.	Update software and reset via service mode.		rafaelmoraes99
PHILCO	PH28D27D	The logo appears and the LEDs turn off, but the sound remains.	Defective LED bars, burned out or shorted LED.	Removing the 2r2 smd resistors (rb13, rb14) to lower the voltage on the leds to 29.2v the television will work normally. In my case, I only removed 1 rb13 resistor and it solved the problem.	JKSTek
PHILCO	PH28D27D	Turns on the logo appears and turns off	Removing the 2r2 smd resistors (rb13, rb14) good luck	Removing the 2r2 smd resistors (rb13, rb14) good luck	JeanJKSTek