Philco Repair Tips
Search: philco
Results: 4775
Results: 4775
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO |
PH39F33DSG LED
|
Turns on, works a little, the screen LEDs start to blink and go out, it appears to be an LED defect | Causes ts 2 power supply transform with cold welding | Ariel Santos | |
| PHILCO |
PH24M LED A2
|
When plugged into the socket, it flashes stand by once and does not turn on | Ic u4 | Ic u4 | RONALDO VIEIRA |
| PHILCO |
TP2920
|
It turns on standby, turns on the power button, it starts and then disarms, but the circuit remains partially connected. | Change two polyester capacitors located on the board next to the main one. c1703 and c1701 | ||
| PHILCO |
PH51U20PSGW
|
It doesn't turn on, it just stays on stand-by | Apparently it would be a software update, but it was the faulty power supply board | Replacing the power supply board | Arnoltec |
| PHILCO |
PH400N
|
Normal stand by you turn on the volume button it turns blue but nothing works | Probably shorted usb reader board and card reader | Release the 2 whips that go to the plate. These two functions will be lost but the device will work again | Magalhães |
| PHILCO |
TP 2054
|
Image warping and turning off | Low primary power supply | Swap d918 and zd908, at the power supply near the c.i. 901 | eletronica fernandes |
| PHILCO |
PH43E30DSGW
|
Does not turn on, nor does standby light up, no signal at all | Main board shorted at 12v and gnd, in the qcpass sector, 2 smd capacitors were shorted, c18 and c19. | The smd capacitors c18 and c19 were replaced, and the problem was solved, it started working normally again. | Adriel SS |
| PHILCO |
PH40E60DSGWA
|
Does not turn on black light | Short in the LED power supply | D81 | Eletrônica Morais |
| PHILCO |
40U16DSG
|
Inoperative, no standby, 12v as soon as it turns on it appears then drops | Qp401, dp401 in short. obs dp401 on this TV was hbr3200(200v,3a) replace it with the one indicated in the mur460(600v,4a) diagram | lgmendes | |
| PHILCO |
40U16DSG
|
Inoperative, no standby, 12v as soon as it turns on it appears then drops | Qp401,dp401 shorted. | lgmendes | |
| PHILCO |
PH21MSS
|
Turns off and goes back to standby | Tl431 trace | Francisco | |
| PHILCO |
PH21SS
|
Heating r.816a, r818 and q802, zd805(11v) with 8v. | S826 47/25 | GDP2 | |
| PHILCO |
PH51U20
|
Without image, with the voltages va and vs | Oxidized control board | Plate replacement | Alex Lopes <small> |
| PHILCO |
PH 21MSS
|
Cushion effect image with vertical curves on both sides | In my case it was in the ew sector of the TV. After a lot of racking my brain I ended up discovering the toasted l451 position coil. | Coil l451 of the ew circuit. (note; in most cases it could be the d454 fr104. good luck and I hope it helps you in some way. | D.S.E.Eletronica |
| PHILCO |
TP1454
|
TV turns on the standby power supply giving 70 volts but it doesn't turn on, the LED goes off after a while and comes back flashing, at no point does the power supply go out of 70 volts, neither in standby nor trying to turn it on | Changed resistor | Changing the resistor, r926 from a 1k | Jr eletrônica |
| PHILCO |
TV PTV32G50SN
|
Does not turn on the LEDs.. | Defect in t con, when you turn it off, the LEDs come back on. | Na t con qe 10 and ct 843 shorted. | Eletrônica Lelo |
| PHILCO |
TV PTV32G50SN
|
Does not turn on the LEDs.. | Defect in t con, when you turn it off, the LEDs come back on. | Na t con qe 10 ct 843 shorted. | Eletrônica Lelo |
| PHILCO |
PH29E52DG
|
Dark image, not LED backlight | Low voltage in dc-dc inverter. 1m resistor rp70 giving 820k. just change. detail, in cp39 and 40 it has to give 45v. | Replace 1MΩ smd resistor position rp70. | NelsinhoPira |
| PHILCO |
TV PH32E31DSGW LED
|
Doesn't start | 3 capacitors in positions c2d7/c1d9/e c2d6 | In my case I had to replace the 3 electrolytic capacitors position c2d7 /each and c2d6 | Airton Filgueira |
| PHILCO |
PH29E52AG
|
Doesn't start | Burned fountain | Icp1 tea1733 , diodo zener zd205 18v . | TV TÉCNICA PARANA |