Philco Repair Tips
Search: philco
Results: 4810
Results: 4810
Make | Model | Symptom | Problem | Solution | By |
---|---|---|---|---|---|
PHILCO |
LCD PH 42M2
T420GW09 |
Vertical lists | After warming up, vertical lists appear with sound | alci fiorin | |
PHILCO |
PH21MSS
|
No sound, total mute | Change resistor r608, 18k, next to the output disconnector | DJ PITUKA | |
PHILCO |
PH42M61DSG
|
Stand by red and does not turn on | Replacement of regulator 805 (1117-33) | Moraes | |
PHILCO |
PH42M6161DSG
|
Stand by red and does not turn on | Replacement of regulator 805 (1117-33) | Pakuko | |
PHILCO |
PTV32G50SN
|
No image, curtain effect | T-con | ||
PHILCO |
PTV32G50SN
HLS78D |
Doesn't start | Replace of power supply resistors rp34 and rp29 (near the trafo and dp7...) | Replace of power supply resistors rp34 and rp29 for 0.1r x 1w | Mauricio-FOCONET |
PHILCO |
PH40E36DSGW
|
Heats up turns off | Leak in the 1mf smd c111 capacitor - just change it | It is next to d5, next to q8, between the micro and the screen's flat cable | SANTOMEL |
PHILCO |
PH49F30DSGAW
|
Doesn't start | Integrated uw1 (qkp36r by , transistor qw2 (t70r380p, resistors rw 6 (360r), rw7 (r300), and rw12(75r) | SANTOMEL | |
PHILCO |
PH49F30DSGAW
|
Doesn't start | Shorted transistor qw3 (mod14n25) | SANTOMEL | |
PHILCO |
PH49F30DSGAW
|
After a few minutes, the screen goes off and tsound is sound | After changing the LED kit and still soldering the wires directly to the LED bars and also to the main board, it didn't solve the problem. | Replace the main board | SANTOMEL |
PHILCO |
PH43C21P
|
Audio cutting sometimes works and stops | Check current transistor q702 that makes the mute | Replace transistor q702 | Luiz videotek |
PHILCO |
PH40U16DSG
|
Calls whenever you want, sometimes doesn't call | Capacitor cp-105 slightly swollen | Replace for another equal or equivalent 400x100f | Maike Sorriso-MT |
PHILCO |
PH40U16DSG LED
|
Heating power supply regulator | Cp105 100x400 low | Trace without testing good luck | Jhone eletronica |
PHILCO |
PH40D10
|
Does not turn on or 12 volt standby LED varies | Dp202 1n4007 open swap | Replace dp 202 | juci |
PHILCO |
PH21M2
|
Low sound, | Replace microns. pins 59 and 58, output 2.5v, it was with 7v and the other with 0v. | DJ PITUKA | |
PHILCO |
PH32E32D
|
Does not come out of stand-by | Ci u807(1.8v regulator) warming up. stand-by on and does not turn on. | Bga microprocessor replacement. msd1309px-lf-z1 | Kabo Informática |
PHILCO |
PH58E51
|
Doesn't start | Tea 1752 | Replace tea 1752 r 10k which feeds pin 16.tea 1755t also. | Eletrônica Lelo |
PHILCO |
PH32U20DG
|
Doesn't start | Shorted processor board | Replacing capacitor c1000, c997 and ci u809 | sergio |
PHILCO |
PH32E32D LED
|
Does not turn on, only the red LED is on | Ci 1117-18 (1.8v regulator) of the main PCI damaged | Replace of ci 1117-18 (1.8v regulator) | sergio |
PHILCO |
PH28N91DSG
|
The LEDs don't light up | Power supply capacitor exhausted | Replace all electrolytic capacitors in the power supply | EletronicaAlmiro |