☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14210
Make Model Symptom Problem Solution By
PHILIPS CP90
Does not have a display Pot. 3896 of 4.7k. goes to pin 13 of the upc
PHILIPS CHASSIS L6.1
Power supply with usual components all shorted R3508 6k8 with intermittent interruptions
PHILIPS 28PW6408/01
Image very open horizontally, without control with mode service. Replacement of transistor 7406 - ktc2800.
PHILIPS 28PW6322/11 CHASSIS MD1.2E AA
Image with excessive width and e/w distortion. switches to stby after a few minutes. Welding on coil 5424 at the junction with c2432. it may damage the mos-fet 7480 mtp3055e.
PHILIPS 36PW6322/11 CH. MD1.2EAA
When turned off on command, the sound is lost but the image remains. R3588 3r3 in the supply, to the cathode of d6590
PHILIPS 28PW9623/12 CHASSIS MD2.25AA
Does not turn on, stays on standby C2418 toasted, replaced, led blinks, +b voltage is already tsound but drops to around 15vts, see: tr7470+7421, t.s.l hr8225 = eldor 1302.0007, finally another tr7408 bsn304 = bsn274, applied a buz90a and it is solved
PHILIPS 21PV267/08
Image shifted sideways Substituir c2584 0.68-250v
PHILIPS 14PT1556 CHASSIS L01.2E
It only tunes to VHF, without sound, the balance control appears and the TV is mono. It also gave error 4 (sound) Turner and eprom reprogramming, as it was corrupted after turning it off/on
PHILIPS 28ML8805/19B FL1.6
After some time of work, the tda3654q and res. r3535 e3536 breakdown Change transformer s.l. hr6538
PHILIPS 28ST2477/10B CHASSI GR2.2 AA
Excessive width C2559 100µf/25v spilled electrolyte corroding the printed circuit under it. pay attention to all the black "nichicon" electrolytic capacitors on the fi module and on the main board, with a tendency to spill the electrolyte.
PHILIPS 21CE4556/10Z CHASSIS 2B
When the volume increased, oscillations appeared in the image D6705. note: the 140v voltage did not adjust when it was 148v +/-
PHILIPS 21PT1664 CHASSI L9.2
Power supply working low Sub t7400 = bf422
PHILIPS 21PT522A CHASSI GR 2.2
No light. with sound Sub t7370 = bc848
PHILIPS 14PT1353/00 CHASSIS L6.1
Does not turn on or light up 6506 rectifier bridge S1NB60, 7504 power supply transistor STP5NB40FP, 6514 Zener BZT03C130, 6502 Zener BZX55C15, R 3514/3515 both 1Ω.
PHILIPS CHASSIS GR1AX
Does not work 1.3 on the 95v line protection activated After removing the protective thyristor, tsound was 99v on the 95v line, which is why the protection was activated. replace r3629 instead of 33k it had 43k, high power supply
PHILIPS 21PT166B CHASSIS AA5
No horizontal deflection, just a vertical line in the center of the screen. 680nf 250v c2450 replacement.
PHILIPS GR1-AX
With about 8 volts instead of 95 on the tht supply 2527 10nf capacitor with leakage, measured with anΩmeter it appeared to be around 500Ω
PHILIPS 14PT1532 CHASSI 6.1
Narrow vertical and folded top Fault c 2404 10n with leak
PHILIPS CH ANUBIS A
Power supply has "+95" with 100v but horiz. does not start Resist. 3444 5k6 2w >> 3w
PHILIPS CHASSIS GR2.1
Green led continuously blinking and voltages on psu output lines fluctuating. 6561 zener 47v. important: the polarity of this zener is incorrectly in one of the faces of the pcb.