Philips Repair Tips

Search: philips
Results: 14210

Make	Model	Symptom	Problem	Solution	By
PHILIPS	21PT5433	Low and vertical audio closed top	Epron / cap.2444 / cap.2465	Rewrite memory and replace caps.	eletronicaapolo
PHILIPS	29PT5642 BOMTEMPO MECATRôNIC	Dead power supply	Pin 4 and 5 of the transformer open	Replace it
PHILIPS	29PT4631	Vertical closed	Fusistor 3488		Eletronica NDN
PHILIPS	14PT519/78R	Does not turn on, there is no + 95 volts at the power supply	The transistor 7521 shorted	Replace the tr with a new one and a hug to the bagpiper	paulo sertel - itararé sp
PHILIPS	21PT5433	Upper vertical strip doubling the image	Capacitor c 2455 10uf/160v	Replace it back to normal	Elephoenix
PHILIPS	20GL1346	Spot effect (i.e. bright spot in the center of the screen when turning off the TV)	Cause c.2737=10n. (modify)	Put one of one of 47 or of 68n.	Armando da eletronica sO TV
PHILIPS	29PT554A 29PT554A	Pertian effect at the bottom of the tube, vertical	Change in values of the 0.22n/63v polyester capacitor, completely changed	Replaced c=2409=0.22nf/63v, close to the vertical output and vertical deflation, replaced and resolved	geraflorem
PHILIPS	29PT9467C/78 000	Pale, hazy and saturated image without definition..	Trc .tube reactivated and defect remedied!	Note-in the writing, small taps on the screwdriver handle on top of the cannon helps! good luck.	Jhone Eletronica
PHILIPS	29PT4635/78R L01	Secondary power supply zero and LED off	Photo coupler	I replaced the photo and the font wobbled. Let's send more tips guys.	This email address is being protected from spambots. You need JavaScript enabled to view it.
PHILIPS	14GL1044	Reduced frame when switching on, normalizes when changing channels	Check if the processor has a 5y termination. If so, replace the pin 35 resistor, which is 47k, with an 8k2 resistor.		Sandro .T. Grachet
PHILIPS	20GL1044	Reduced frame when switching on, normalizes when changing channels	Check if the processor has a 5y termination. If so, replace the pin 35 resistor, which is 47k, with an 8k2 resistor.		Sandro .T. Grachet
PHILIPS	25PT6641	Does not oscillate	Ci7104 smd mosfet horizontal draive line		tecnicagil
PHILIPS	29PT5635	Fountain did not break, did not oscillate	A photo coupler c817	Photo coupler	lucie angelo santos
PHILIPS	20PT324A	All green screen with lines	Defective tube socket		BETO ELETRONICA ACRELANDIA AC
PHILIPS	MG2.1E MG2.1E	Image with flickers changing the color tone, sometimes return lines appear	Some wear on the kinescope which causes changes in the beam current regulated by the tda9330h	Replace tda's 6101q or 6111q and increase cathode current by replacing the 47r resistor r3360 blc-info line with a 220k trimmer, adjusting in order to stabilize the balance between cathodes in conjunction with the g2 tuning	João
PHILIPS	21PT5433 L03.1	(attention) guys, after changing the feet of the 7n80 power supply, which was shorted, the TV kept turning off before the image appeared	R 3526 0.15r changed put a new one because in the test it was good. a tip to know if the defect is that it jams with a piece of wire if the TV works normally you can change the resistor	Replacelo	antonio nobrega(patos pb)
PHILIPS	29PT554	Power supply weapon tries to turn on and goes back to standby after opening it turned on once normally and turned off by itself, continuing the previous defect	Solda fria no ic 7401 impersetivel cases	The IC was resoldered, returning to normal operation	Ricardo Pereira
PHILIPS	29PT9467C SK5.1L	Burns q 905,904	C 904 shorted 100n	Replace transistors, resistors and capacitor.	ALEX/FETTER
PHILIPS	14PT218A	Black band at the bottom of the screen without audio	Faulty memory	After replacing the ci24c08wp it worked normally	Beto Eletronica Acrelandia AC
PHILIPS	29PT4631	Turning off	Bad power supply transistor or cable see how to identify	First replace the transistors bc 337,327 and the cap 47/25 if that doesn't help, turn on the TV and keep changing the channel, if while you replace the channel it doesn't turn off (do this test for about 2 min) it's probably the tube, being the tube there are only two alternatives, replace it or find a way to make it work (connecting 3 4148 diodes to the rgb, joining the anodes and connecting to the ik in front or behind the r 3204, enters the setup, adjusts the colors and the cl to 14, screen, etc.) and thau	JURANDIR