Philips Repair Tips

Search: philips
Results: 14231

Make	Model	Symptom	Problem	Solution	By
PHILIPS	42PFL3403 32PFL3403	Standby LED turns on but TV doesn't start	Resolder resistors and diodes next to the relay		RMSELETRONICA
PHILIPS	42PFL3403	Standby LED turns on but TV doesn't start	Connect with the control		RMSELETRONICA
PHILIPS	42PFL3604/78	Doesn't start	Mainboard repair	Check diode d4 and u14 close to the control connector on the main board. First activate the power supply if it generates 3.3v 24v then see if capacitor c168 and c159 is heating up.	JORGE TV TÉCNICA PARANÁ
PHILIPS	42PFL5403	Does not hit the relay, starts from stand by to turn on but does not hit the relay	Lack of main drive	Ground the standby which will hit the relay then press channel + and the TV will turn on.	ANDREI LOWE
PHILIPS	42PFL3507D/78	Power supply inoperative. primary power supply ok, but no voltage at the outputs and no standby.	Capacitor c9353 (330uf x 16v) with changed value and capacitor c9354 (470uf x 16v) shorted.	Replace the two capacitors.	Pixel Assist
PHILIPS	20PT3331/78	Short fly-back	Fly-back	Replace o fly-back jf0501-19255	Sinailson furtado
PHILIPS	32PF3403/78	TV won't turn on dead power supply without 3.3vsb	2.2uf smd capacitor in position c908 and the 431l smd transistor in position ic951. both shorted	Replace them and give power to the TV.	Francisco Melo - Parintins-Am
PHILIPS	55PFG5100/78	When turned on, the normal logo appears and when you place any signal on any input, the image appears bluish.	Software contamination	Enter the menu and give factory mode (reset)	SANTOMEL
PHILIPS	32PFL3017H/12	Does not turn on, LED is off. 5v standby voltage becomes about 2v	330uf/16v capacitor c9353 in the standby power supply (if you measure it, it will appear to be normal)	Replace with a 470μF one	helderasf
PHILIPS	FWM653/55	Standby does not turn on, shock opened CD board	Resolved		Carlos A Silva
PHILIPS	20PT3336/78	Turns on and off in seconds	Cold solder on the smd resistors next to the flipback	Resolder all SMD close to the flyback.	MARCONES DE ARARIPINA-PE
PHILIPS	32PFL4606	It would start making a hissing sound like it was audio without an antenna and it would turn off	I released the speakers and the hissing noise remained, it was a high voltage leak.	It was the transformers, one was leaking internally, as tsound was an inverter board, I replaced the entire board, it solved the problem.	edmilsonpimentel
PHILIPS	20PT3331	LED comes out of stand-by but does not work	Several cold welds on the processor		AMERICO BREJO-PE
PHILIPS	40PFL3606D/78	It didn't turn on completely dead.	Damaged components, fuse (f101), transistor (6n80c) replaced by k13a65d, and (c502).	Mkps	Marciok mkps
PHILIPS	42PFL3605D/78	Power supply does not turn on, does not output 3.3v,	10k/1kv c120 with leakage	Replace c120	Gabriel GXP
PHILIPS	32PFL3606	Doesn't start	Tsound is only 3.3v at the power supply	Cause, capacitor shorted next to the coil (dc dc converter), 2105. (thriller motherboard). ci 7122 heated up.	Maurilio
PHILIPS	43PFG5100	No image, backlight on	C103	Remove or replace capacitor c103 on the display board	FABRICIO
PHILIPS	21PT9467C/78	Replace 220k 626 resistor	R 626 220k changed or opened	Replace 220k 626 resistor	eletronica global chiquinho
PHILIPS	32PFL3404/78	TV doesn't turn on	This TV has a system that is as follows: if you turn it off using the control, it will only turn on again through it and if it turns off using the power button, in the same way it will only turn on again through it.	Connect with control	Antonio Carlos (Eletrônica Renascer)
PHILIPS	32PFL3606D/78 L11M1.1L LA	Noisy backlight and the inverter turning off	R41 (68k) open	Replace of r41 (68k) on the inverter board, it is close to the frequency adjustment potentiometer	leitemarcellus