Philips Repair Tips

Search: philips
Results: 14231

Make	Model	Symptom	Problem	Solution	By
PHILIPS	32PFL3406D/78	Does not tune channels	Reg. 7123 de 5v		Imagem
PHILIPS	40PFL5605D	Stuck in standby	It seemed to be a defect but it wasn't, it was a remote control that wasn't original and, when turned off by it, the TV went into standby and didn't come out again. The procedure was carried out by holding down vol+ and then turning on the main switch until the TV turned on, then with Using the original control, it turned off and on again and the problem was resolved	Here's a tip: control for this TV model only the original	PATRICK ELETRÔNICA
PHILIPS	42PFL3604	Turns on and after 3 seconds it disables the invert dark screen on one side the normal sound continues	Good inverter transformer reference values t903 and 904 in 18.1Ω / l= 150 mh out 1.1Ω / l6.07 mh, tested with esr02 pro	Changing the replaced traffic!	BRUSKE
PHILIPS	32PHG4900 32PGH5000 TPM10.1L	Inverted image after board change.	Access service mode (menu+1999+return). 1st navigate to option 74 (flip panel), press the right arrow on the remote control to enable the flip panel option from off to on. 2nd navigate to option 19 (virgin mode), press the right arrow on the remote control, to enable the virgin mode option, from off to on. Turn off the device using the remote control. wait a few seconds and turn it on again.	Credit to maikon ramos from eletronicabr.com (I only corrected the Portuguese errors. lol).	Eletrônica R-Tec
PHILIPS	HTS3576	I'm sound	Som plate		Wellington Brandão de Farias
PHILIPS	39PFL4707G	Inoperative led off	C9303 e c9304	Replaces	Carlos eletrônica
PHILIPS	20PT4331/78	Charred resistors	R3443 eo r3444	Replace o r3443 of 1r eo r3444 of 3r3	Sinailson furtado
PHILIPS	20PT4331/78	Normal switching on gives sound but no image and OSD appears but the screen is dim.	R3442	Replace the 150k r3442 and the TV will work normally. God be praised!	Sinailson furtado
PHILIPS	29PT4635/78	Sometimes it doesn't turn on. but when it turns on, it turns off randomly after some time.	Source opto-coupler, code 7515. It was leaking and it is only possible to check the leak with it outside the circuit and with an analog multimeter in the x10k range.	Replace the opto-coupler	Manoel Almeida
PHILIPS	14PT316A	TV doesn't turn on, voltage +b keeps oscillating and the standby LED flashes twice with a long stop	Power supply	Replace capacitors 2530 of 1mf/50v and 2540 of 100mf/25v.	DANGRA ELETRÔNICA SÃO PAULO
PHILIPS	42PFL3604	It turns on, sometimes the screen lights up, sometimes it turns on all the normal power supplys, the lamps don't light up, no sound.	See c104, escape, outside of normal capabilities.	Replace c104.	arock
PHILIPS	21PT6456	League goes into protection right away	C 2444		Flavio
PHILIPS	43PFG5000/78	Just turn on the LEDs and have audio	Tsound is no image, only sound		José Roberto
PHILIPS	NTRX500 NTRX700 NX5 NX7	When turned on, it turns off, stand by remains on	Natural wear and tear	Replace r785 r786 68k smd next to l715	iNOVA ELETRONICA
PHILIPS	39PFL3008D	Lights up, does not show an image and turns off, only turning on again when unplugged	Corrupted eeprom	Record u402 with the file downloaded directly from the link https://www.philips.com.br/c-p/39pfl3008d_78/3000-series-tv-led-fina-full-hd-com-digital-crystal-clear/suporte, tsound will be 3 items, use the file corresponding to the display model used on your TV to record the eeprom, if it is upside down, type menu, 1999, return, and restart the system.	davi.sls
PHILIPS	42PFL5432	No image	Ci mu1 bd9897fs smd and zener mzd2 6.2v, on one of the inverter boards		Eletrônica Cecé. Brumadinho MG
PHILIPS	32PFL3606D	Dead	Only 3.3v present in the power supply - shorted capacitor (no number on the board) on the main PCI on pin 2 of the IC 7122.		MARCOS COELHO
PHILIPS	FWM570/19	Call then call	Transistor smd 7505	Not necessary	edval
PHILIPS	14PT 3336	Off standby hits the relay and does not turn on.	C2525 de 10mf/50v		eletronica do gilvan
PHILIPS	32PFL3008D/78	Does not turn on backlight and starts normally	Pin 1 connection of main board and bios damaged	Pin 1 on the main board did not make contact, and replacement of the bios with a new one	rikadapper