Search: philips
Results: 14231
Make Model Symptom Problem Solution By
PHILIPS 42PFL3707D/78
TPM9.1LA
Doesn't start. Power supply with low 12v line power. Changing the capacitors on the 12v line. c9169 (330x25v), c9168 (330x25v), c9163 (330x25v) and c916 (330x25v). Eletrônica R-Tec
PHILIPS 40PFL5606
Doesn't start Power supply ci and transformer Ci lnk362 and transformer replace hi two cleber lima rs
PHILIPS 26PFL3404 32PFL3404 42PFL3404
Does not turn on, then turns on the back light, beeping the audio and turns off, i.e. various faults Change all the smd capacitors on the main board: 10x16, 100x16, 47x16, 4.7x16 and then leave to soak in esopropyl alcohol. Replace all the smd capacitors on the main board: 10x16, 100x16, 47x16, 4.7x16 and then leave to soak in alcohol <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
PHILIPS 42PFL3403
Erasing screen Cold solder on the c700 close to the inverter transformer Resolda do c700 Marcelo Piranga
PHILIPS FWP2000X/78
Does not accept power, only has a red standby LED on, 5 volt power supply speaking 12v power supply on the power supply board is missing and the 5v that derives from it is also missing. Replace d711 (her105) and check q704 fet (ao3401) and q706 fet (ao3402), both smd MIGUELTV
PHILIPS 42PFL5332/78
Does not turn on, the blue light comes on, pressing the on and off button, the blue LED just blinks Reverse right side, 02 cap 470uf x 35v swollen and reverse left side with 02 fdd8447l shorted The cap 470μF 35v and fdd8447l components were replaced AdFur
PHILIPS 20PT529A/78
Inoperative, nothing turns on when pressing the power button on the remote control, the stand bay led only blinks but does not help. heating the axillator with a hairdryer makes the tv axilla normal! Aoxilator Replace the aoxilator tda9570h/n1/a/0646 Sinailson furtado
PHILIPS 32PFL5604D/78
When plugging in the socket, it comes with a blue screen, without IR controls and buttons. A visual inspection has already determined, c-100, c-104 and c-87 "stuffed" I replaced them and ran for the hug. Robusto
PHILIPS 170S6FS/78
Turns on, shows video and turns off the screen brightness. Capacitor c215 at the power supply. Capacitor replaced. KABO Info
PHILIPS 29PT4647/78
Disconnecting as if it were a weak tube Changed coil 5342 on the kinescope board By a resistor and 1r JRN eletronica
PHILIPS 29PT6456
Turns on but the tube doesn't light up or sound It has a burnt tantalo capacitor and has no identification LUIZ SERGIO RODRIGUES
PHILIPS 32PHG5102
Power supply with mosfet and ci reg smd and blown resistors Replacement of ic9101, r9109, 9110, 9113, 9101, d 9105, q9101 and the cause of the defect c9126 As it is difficult to find the schematic I will leave the component values ​​r9109=10Ω, r9111=10k, r9110=47Ω, r9113= 1k, r9114=110k, r9146= 0Ω, r9101=0.27Ω, d9104,9105 ,9106=1bh62, q9101=2n6659 or k8a65d, ic9101=pf6005ag or pf6003ag, c 9126= 100pf/1kv ROBERTO BRUSKE youtube
PHILIPS 32PW8422/78
L05L AA
It doesn't turn on, sometimes it turns on and off, Replace cap 2510 and 2511,22uf 50v, resistor 3401 47k. at the power supply DJ PITUKA
PHILIPS 39PFL4707
The TV turns on more if it turns off, it no longer turns on, the voltage on the u701 regulator is high. Change the 3.3volt regulator u701 on the main board. Replace u701 in the main. <small>wellingtoneletronicasilva@ bol.com.br</small>
PHILIPS 40PFG6309
TV when turned on seems to work normally after a few seconds it restarts Corrupted u402 flash memory replace Paulo Pinho
PHILIPS 40PFG6309
Gets a bluish image on tv and hdmi normal characters Restoration is done and returns normal but after a while it turns blue again, corrupted memory u404 replace Paulo Pinho
PHILIPS 20PT4331/78
Alloy with a black band at the top of the screen and with retraction lines Cause capacitor 2465 Replace of the same ASSISTEC
PHILIPS 20PT4331
Does not turn on pulsating power supply Cause photo coupler and tr bc547b Replace of the same ASSISTEC
PHILIPS 40PUH6400/88
QM15.2E
Turns on without image but with sound. Defect in led bars Pablo
PHILIPS 29PT8457/78
SL40 11
TV turns on with a vertical risk, but shakes and turns off, but the risk doesn't reach from one end to the other I replaced the 2µ2 capacitor c2415 with 160 giving 1.8... close to the horizontal fitting. resolved the problem. Francisco Melo - Parintins-Am