Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
FL4.17
|
Bad synchronization with external signals | Delete position 3115 on the eco 100hz box. remarks : introduced in production in week 9415. | ||
| PHILIPS |
FL4.17
|
Bad picture. picture scrolls. no rc reaction. | +5v was 4,1v instead of 5,1v. replace ic7551 (lm358n; 4822 209 70672) | ||
| PHILIPS |
FL4.17
|
Bad pict. no menu. dark bars over pict. red pict. in dig.scan mode. | +5v was 4,3v instead of 5,1v. ic7551 (lm358n 4822 209 70672) defective. ic7209 (saa7158 4822 209 31059) bendic defective. | ||
| PHILIPS |
FL4.17
|
Bad focus or focus varies in a new set or after crt replacement | Possible solution: short circuit the focus and the g2 pins of the picture tube with the aquadag coating. switch the set on for approximately 5 seconds. after this return the set to its original condition. check if the focus adjusted normally. if not repla | ||
| PHILIPS |
FL4.17
|
Antenna input: no sound. external input: sound o.k. | Check whether crystal 1602 (stereo decoder) 10mhz oscillates. if not replace x1602 (4822 242 80276). | ||
| PHILIPS |
FL4.17
|
After 10 minutes picture becomes red from right side | C2395 on the lsp poorly soldered. | ||
| PHILIPS |
FL4.17
|
"nvm write protection enabled" message on screen. | Startup problem or 'nvm write protection enabled' message on screen after replacement of nvm (st24c08cb1; 4822 209 32283) with a st24c08cb6 (4822 209 33113). use as replacement the st24c08 1 (9311 021 36682). | ||
| PHILIPS |
FL4.16
|
Supply switch-off sometimes | Check the +5 stand-by. this voltage has to be 5.5v and may not vary. when the voltage drops below 5.2v the set switches-off. cure: check leakage of d6266 (bzx79/f6v8; 4822 130 34278) | ||
| PHILIPS |
FL4.16
|
Supply +5v too low, black horizontal bar in picture. bad sync. | Check/replace ic7551 (lm358n; 4822 209 70672) | ||
| PHILIPS |
FL4.16
|
Sound shuts off and osd in picture. | Voltage on pin 4 tda8417 was 3.5v tt instead of >4.5v tt. replace x-tal 10 mhz (4822 242 80276). | ||
| PHILIPS |
FL4.16
|
Sometimes vibration in vertical direction. | Replace c2410 (150nf 5%; 4822 121 41854) on lsp. | ||
| PHILIPS |
FL4.16
|
Sometimes in protection, or hor. width varies | Check or resolder on lsp the pins of e/w bridge coil 5521. | ||
| PHILIPS |
FL4.16
|
Shuts off and on again on pr.nr. 1 after 3 hours. | D6272 (bzx55b5v6) interruption when it becomes hot. | ||
| PHILIPS |
FL4.16
|
Set totally inoperative, no leds on. supply hums. | R3252 220 kΩ (start-up micro-sops) defective (4822 116 52258). | ||
| PHILIPS |
FL4.16
|
Set inoperative only red or green led. supply was 141v but no eht. | Line drive puls for t7506 (2sc4288a) too low. l5503 defective (line drive coil; 4822 157 63252) | ||
| PHILIPS |
FL4.16
|
Set can only be operated with remote control | Check whether "child lock" is disabled. to check this, see "frequently asked questions", "how to disable child lock". | ||
| PHILIPS |
FL4.16
|
Picture twists from top | Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c3v6; 5322 130 34834 or bzx79/c10; 4822 130 61219) | ||
| PHILIPS |
FL4.16
|
Picture ok after some time | Ic7207 (sda9205-2; 4822 209 31056) defective when set is cold. | ||
| PHILIPS |
FL4.16
|
Picture gives black horizontal stripes, also on rgb | Ic72027 sda9205-2 lfr box defective (4822 209 31056). | ||
| PHILIPS |
FL4.16
|
Overview of sops repair kits | Overview of sops repair kits ---------------------------- fl1.0 ag00 upto ag03 4822 310 20492 fl1.0 ag04 and higher 4822 310 31921 fl1.0s 4822 310 31924 fl1.1 25" and 28" 4822 310 31919 fl1.1 33" 4822 310 31932 fl1.1s |