Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
FL4.26
|
Osd, txt, sound, colours ok, no y signal. | C2396 (22nf) leakage (4822 126 11544) | ||
| PHILIPS |
FL4.26
|
Noise on high volume | Perform the following modifications on the ssp: add on position 3618 4,7nf (4822 122 31784) add on position 3619 jumper (4822 051 10008) connected in series from 2604/4610 to earth. change position 4610 into 1kΩ (4822 051 10102) | ||
| PHILIPS |
FL4.26
|
No sound, "on, standby, i" leds blinking | 10mhz crystal 1602 on the ssp defective, 4822 242 80276 | ||
| PHILIPS |
FL4.26
|
Low brightness txt and osd, picture ok | If this condition occurs, check the option codes. resetting the option code numbers as per the service manual provided the cure. | ||
| PHILIPS |
FL4.26
|
In default mode err.99, blinking leds. no +5.4v on pin 8 l02 | Ic7551 lm358n defective +5/13v, replaced. (4822 209 70672) cause: bridge 9240 interrupted. | ||
| PHILIPS |
FL4.26
|
How to enable/disable "child lock" | Press "menu" button on remote control. when the menu appears on the screen, you select "special features" (this expression is language dependent) within "special features", the "child lock" can be enabled or disabled. | ||
| PHILIPS |
FL4.26
|
Four dark bars over the picture. | The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672). | ||
| PHILIPS |
FL4.26
|
Foggy picture/fly back lines/protection | Check/replace r3517 1Ω on lsp (4822 052 11108). | ||
| PHILIPS |
FL4.26
|
Dark picture, only green led, no menu or osd. | +5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954). | ||
| PHILIPS |
FL4.26
|
Dark fuzzy picture. osd and menu not in focus. | +5v was 7.8v and +13v was 15.5v ic7551 (lm358n; 4822 209 70672) defective. | ||
| PHILIPS |
FL4.26
|
Correction to service information fl 95.01 | Correction to service information fl 95.01 ------------------------------------------ correction in the overview of 100hz and proscan boxen. the replacement for service code 4822 212 30534 must be 4822 212 31231 the replacement for service code 4822 21 | ||
| PHILIPS |
FL4.26
|
Correction to service information fl 95.01 | Correction to service information fl 95.01 ------------------------------------------ correction in the overview of 100hz and proscan boxen. the replacement for service code 4822 212 30534 must be 4822 212 31231 the replacement for service code 4822 21 | ||
| PHILIPS |
FL4.26
|
Both languages can be heard by dual nicam signals | For fl1-ptv change the software into v89; 4822 900 10732 for all other fl sets change the software into v88; 4822 900 10723 remarks :introduced in production from week 9614 onwards. | ||
| PHILIPS |
FL4.26
|
Blank picture. osd not synchronised and too large, no txt. | Check/replace memory ic 7900 (st24c08cb1; 4822 209 32283). | ||
| PHILIPS |
FL4.26
|
Bad picture. picture scrolls. no rc reaction. | +5v was 4,1v instead of 5,1v. replace ic7551 (lm358n; 4822 209 70672) | ||
| PHILIPS |
FL4.26
|
Bad pict. no menu. dark bars over pict. red pict. in dig.scan mode. | +5v was 4,3v instead of 5,1v. ic7551 (lm358n 4822 209 70672) defective. ic7209 (saa7158 4822 209 31059) bendic defective. | ||
| PHILIPS |
FL4.26
|
Bad focus or focus varies in a new set or after crt replacement | Possible solution: short circuit the focus and the g2 pins of the picture tube with the aquadag coating. switch the set on for approximately 5 seconds. after this return the set to its original condition. check if the focus adjusted normally. if not repla | ||
| PHILIPS |
FL4.26
|
"nvm write protection enabled" message on screen. | Startup problem or 'nvm write protection enabled' message on screen after replacement of nvm (st24c08cb1; 4822 209 32283) with a st24c08cb6 (4822 209 33113). use as replacement the st24c08 1 (9311 021 36682). | ||
| PHILIPS |
FL4.17
|
Wrong synchronization, unstable colors | D6417 on the lsp dependent on temperature, check/replace (4822 130 81223) | ||
| PHILIPS |
FL4.17
|
Wrong service batch of st24c08cb1 memory ic's | Wrong service batch of st24c08cb1 memory ic's 4822 209 32283 ------------------------------------------------------------ temporarily a wrong batch of earom's has been delivered, causing the fault "nvm memory not write protected" after replacing the earom |