☰

Philips Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: philips
Results: 14210
Make Model Symptom Problem Solution By
PHILIPS FL4.16
Overview of doors for fl4 styling Overview of doors for fl4 styling --------------------------------- 4822 432 93229 door for 29" fl4.17/fl4.27 4822 432 93393 door for 29" 4gfl2.20e aa 4822 432 93312 door for 29" fl4.16/fl4.26 4822 432 93382 door for 29" gfl2.20e ab 4822 432 93271 do
PHILIPS FL4.16
Noise on high volume Perform the following modifications on the ssp: add on position 3618 4,7nf (4822 122 31784) add on position 3619 jumper (4822 051 10008) connected in series from 2604/4610 to earth. change position 4610 into 1kΩ (4822 051 10102)
PHILIPS FL4.16
No sound, "on, standby, i" leds blinking 10mhz crystal 1602 on the ssp defective, 4822 242 80276
PHILIPS FL4.16
Low brightness txt and osd, picture ok If this condition occurs, check the option codes. resetting the option code numbers as per the service manual provided the cure.
PHILIPS FL4.16
How to enable/disable "child lock" Press "menu" button on remote control. when the menu appears on the screen, you select "special features" (this expression is language dependent) within "special features", the "child lock" can be enabled or disabled.
PHILIPS FL4.16
Four dark bars over the picture. The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672).
PHILIPS FL4.16
Dark picture, only green led, no menu or osd. +5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954).
PHILIPS FL4.16
Dark fuzzy picture. osd and menu not in focus. +5v was 7.8v and +13v was 15.5v ic7551 (lm358n; 4822 209 70672) defective.
PHILIPS FL4.16
Correction to service information fl 95.01 Correction to service information fl 95.01 ------------------------------------------ correction in the overview of 100hz and proscan boxen. the replacement for service code 4822 212 30534 must be 4822 212 31231 the replacement for service code 4822 21
PHILIPS FL4.16
Correction to service information fl 95.01 Correction to service information fl 95.01 ------------------------------------------ correction in the overview of 100hz and proscan boxen. the replacement for service code 4822 212 30534 must be 4822 212 31231 the replacement for service code 4822 21
PHILIPS FL4.16
Both languages can be heard by dual nicam signals For fl1-ptv change the software into v89; 4822 900 10732 for all other fl sets change the software into v88; 4822 900 10723 remarks :introduced in production from week 9614 onwards.
PHILIPS FL4.16
Blank picture. osd not synchronised and too large, no txt. Check/replace memory ic 7900 (st24c08cb1; 4822 209 32283).
PHILIPS FL4.16
Bad picture. picture scrolls. no rc reaction. +5v was 4,1v instead of 5,1v. replace ic7551 (lm358n; 4822 209 70672)
PHILIPS FL4.16
Bad pict. no menu. dark bars over pict. red pict. in dig.scan mode. +5v was 4,3v instead of 5,1v. ic7551 (lm358n 4822 209 70672) defective. ic7209 (saa7158 4822 209 31059) bendic defective.
PHILIPS FL4.16
Bad focus or focus varies in a new set or after crt replacement Possible solution: short circuit the focus and the g2 pins of the picture tube with the aquadag coating. switch the set on for approximately 5 seconds. after this return the set to its original condition. check if the focus adjusted normally. if not repla
PHILIPS FL4.16
"nvm write protection enabled" message on screen. Startup problem or 'nvm write protection enabled' message on screen after replacement of nvm (st24c08cb1; 4822 209 32283) with a st24c08cb6 (4822 209 33113). use as replacement the st24c08 1 (9311 021 36682).
PHILIPS FL2G
Pix folded at the bottom Change capacitor 2652 (1000 mf/50 volts). 2652 is filter cap for -14v supply.
PHILIPS FL2G
No picture or blue mute when other equipment is used in search mode Disable the blue mute by changing the option code. decrease the original value with one.
PHILIPS FL2G
High failure of ptc For main input 100v: change position 3020 and 3021 on the large signal panel into 4822 116 40277 for main multi voltage: change position 3020 and 3021 on the large signal panel into 4822 116 40247 remarks : introduced in production in week 9550
PHILIPS FL2G
Dark pix. no luminance (y) signal. Cap 2327 (100nf) on ssp between pin 15 of ic 7324 (tda4670) and ground leaky. no `y' output from tda4670. replace 2327.