Philips Repair Tips
Search: philips
Results: 14245
Results: 14245
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
FL1.10
|
Jitter | In pip unit change the value of r3336 to 4k7. | ||
| PHILIPS |
FL1.10
|
How to enable/disable "child lock" | Press "menu" button on remote control. when the menu appears on the screen, you select "special features" (this expression is language dependent) within "special features", the "child lock" can be enabled or disabled. | ||
| PHILIPS |
FL1.10
|
Horizontal oscillator not stable. | For a more stable adjustment of the horizontal oscillator change the next items on the large signal panel: position 3405 from 30k into 33kΩ (4822 051 10333) position 3406 from 10k into 4k7Ω (4822 100 11319) remarks : introduced in producti | ||
| PHILIPS |
FL1.10
|
Goes to st/by at sw on & chan change - pic too big | Ht high at 156v (141v), r3374 75k had increased in value | ||
| PHILIPS |
FL1.10
|
Four dark bars over the picture. | The +5 volt was 5.6 volt instead of 5.1 volt. check/replace ic7551 (4822 209 70672). | ||
| PHILIPS |
FL1.10
|
Fault guide | See tv mag nov 2000 | ||
| PHILIPS |
FL1.10
|
Fall off position 3204 on the large signal panel | Fall off position 3204 on the large signal panel ------------------------------------------------ when position 3204 (ntc/ptc; 4822 116 40215) on the lsp is defect it is recommended to replace it by a ptc/ptc (4822 116 40253). together with this change al | ||
| PHILIPS |
FL1.10
|
Dead - no volts to mains cap | Positor ph95315 & fuse | ||
| PHILIPS |
FL1.10
|
Dark picture, only green led, no menu or osd. | +5v supply was 4,1v. voltage d6551 was 4,3v instead of 5,6v. check/replace d6551 (4822 130 80954). | ||
| PHILIPS |
FL1.10
|
Crazy behaviour: no response from rc or controls. | Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v82 (4822 900 10423). for easy mounting also the controlboard 7115 (on ssp) can be replaced by | ||
| PHILIPS |
FL1.10
|
Crazy behaviour: no response from rc or controls. | Other phenomenas: volume up/down, spontanuous service mode etc. etc. in areas with top-teletext. replace control software by replacing eprom ic7002 to version v83 (4822 900 10506). for easy mounting also the controlboard 7115 (on ssp) can be replaced by | ||
| PHILIPS |
FL1.10
|
Correction to product survey 1996-4 | Correction to product survey 1996-4 (4822 727 21505) ---------------------------------------------------- on page pcs 41989 is mentioned at: fl1.10 ag11 and higher: control panel 4822 212 31708 fl1.17 ag20 : control panel 4822 212 31708 fl | ||
| PHILIPS |
FL1.10
|
Colors flicker when the set is warm or poor colors | Check ic7366 color signal delay circuit (tda4660). replace by tda4661 (4822 209 31714). when tda4660 is replaced by tda4661 also change the following components: - delete 2386, 3385 - change 3383 into 33k (4822 051 10333) - c | ||
| PHILIPS |
FL1.10
|
Colored picture or picture is green/red, fly-back lines | Check zenerdiode 6450 on pin 19-ic7430 on the lsp. new diode must be philips (telefunken does not work), 4822 130 81512 | ||
| PHILIPS |
FL1.10
|
Bux85f in mikrosops defective | Change the value of c2260 to 4n7f, replace 7270 with transistor bd825 (4822 130 41746). | ||
| PHILIPS |
FL1.10
|
Both languages can be heard by dual nicam signals | For fl1-ptv change the software into v89; 4822 900 10732 for all other fl sets change the software into v88; 4822 900 10723 remarks :introduced in production from week 9614 onwards. | ||
| PHILIPS |
FL1.10
|
Blank picture. osd not synchronised and too large, no txt. | Check/replace memory ic 7900 (st24c08cb1; 4822 209 32283). | ||
| PHILIPS |
FL1.10
|
Bad picture. picture scrolls. no rc reaction. | +5v was 4,1v instead of 5,1v. replace ic7551 (lm358n; 4822 209 70672) | ||
| PHILIPS |
FL1.10
|
Bad pict. no menu. dark bars over pict. red pict. in dig.scan mode. | +5v was 4,3v instead of 5,1v. ic7551 (lm358n 4822 209 70672) defective. ic7209 (saa7158 4822 209 31059) bendic defective. | ||
| PHILIPS |
FL1.10
|
Bad focus or focus varies in a new set or after crt replacement | Possible solution: short circuit the focus and the g2 pins of the picture tube with the aquadag coating. switch the set on for approximately 5 seconds. after this return the set to its original condition. check if the focus adjusted normally. if not repla |