Philips Repair Tips
Search: philips
Results: 14246
Results: 14246
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
FL1.10
|
Various faults can be observed. | Check the earth connection from the ssp: connect earth tuner with earth line output transformer (lsp) to find-out whether the problem is solved. check connectors l02 and s02 pins 1,2 (sometimes only 7 wires are used in the connector) | ||
| PHILIPS |
FL1.10
|
Unstable picture, horizontal jitter. | Check/replace r3405 on the lsp. (4822 051 10303 for 50 hz sets; 4822 051 10333 for 100 hz sets). | ||
| PHILIPS |
FL1.10
|
Tuning does not function | Resistor r3240 on lsp in v-tuning wire broken. | ||
| PHILIPS |
FL1.10
|
Totally inoperative. only red led on. | Check line driver transformer l5503 on lsp (4822 142 40328). | ||
| PHILIPS |
FL1.10
|
Totally inoperative. | Transistors 7250 (bux85f; 4822 130 62509) and 7251 (bc848; 4822 130 61207) in microsops defective. or d6251 (llz-c5v6; 4822 130 80954) and r1250 (=r3230; 1Ω; 4822 052 10108) defective. or t7270 (bd825; 4822 130 41746) or t7201 (bc857c; 5322 130 427 | ||
| PHILIPS |
FL1.10
|
Total inoperative, leds blinking, error 99 | Check and replace if necessary c2504 and/or 2505 (2kv hrr) on the large signal panel. replace by a 3kv15 hr-r capacitor if possible: 820pf 4822 126 13152 1nf 4822 126 13153 1,2nf 4822 126 13154 1,5nf 4822 126 13155 1,8nf 4822 126 13156 2, | ||
| PHILIPS |
FL1.10
|
Synchronization, picture disappears | D6703 and t7704 defective on picture tube panel. | ||
| PHILIPS |
FL1.10
|
Supply switch-off sometimes | Check the +5 stand-by. this voltage has to be 5.5v and may not vary. when the voltage drops below 5.2v the set switches-off. cure: check d6266 for leackage (bzx79/f6v8; 4822 130 34278) or check t7268 for leackage (bd943f; 4822 130 62742). the 5.5v is meas | ||
| PHILIPS |
FL1.10
|
Supply +5v too low, black horizontal bar in picture. bad sync. | Check/replace ic7551 (lm358n; 4822 209 70672) | ||
| PHILIPS |
FL1.10
|
Stripes in picture and after about 5 min. only snow. | Replace tuner fq916bl (4822 210 10565). | ||
| PHILIPS |
FL1.10
|
Spook in picture | Use special antenna cables. codenumbers: 4822 321 61224 pal 1 meter 4822 321 61225 pal 2 meter 4822 321 61226 secam 1 meter 4822 321 61227 secam 2 meter | ||
| PHILIPS |
FL1.10
|
Splitted characters with txt (bad starting of dvtb). | Add r3100 (1m 5% 0,5 w; 4822 116 52235), between pin 7 and pin 15 of ic7111 (saa9042) on the lfr box. change 4108 into 220nf 50v (4822 122 32927) on the lfr box. remarks : introduced in production in week 9333. | ||
| PHILIPS |
FL1.10
|
Sometimes vibration in vertical direction. | Replace c2410 (150nf 5%; 4822 121 41854) on lsp. | ||
| PHILIPS |
FL1.10
|
Sometimes set switched back to standby. only red led on. | Microprocessor panel defective (4822 212 30803 and 4822 900 10423) | ||
| PHILIPS |
FL1.10
|
Sometimes in protection, or hor. width varies | Check or resolder on lsp the pins of e/w bridge coil 5521. | ||
| PHILIPS |
FL1.10
|
Set inoperative only red or green led. supply was 141v but no eht. | Line drive puls for t7506 (2sc4288a) too low. l5503 defective (line drive coil; 4822 157 63252) | ||
| PHILIPS |
FL1.10
|
Set can only be operated with remote control | Check whether "child lock" is disabled. to check this, see "frequently asked questions", "how to disable child lock". | ||
| PHILIPS |
FL1.10
|
Poor colors, shaking picture | Check ic7366 color signal delay circuit (tda4660). replace by tda4661 (4822 209 31714). when tda4660 is replaced by tda4661 also change the following components: - delete 2386, 3385 - change 3383 into 33k (4822 051 10333) - c | ||
| PHILIPS |
FL1.10
|
Pip picture not in order. | Check r3345 (4822 111 41424) in pip unit, check ic7755 (4822 209 63423). | ||
| PHILIPS |
FL1.10
|
Picture twists from top | Voltage of pin 8-ic7450 (tda3654q) on the lsp has raised to ca. 20 v. check diode 6451 (bzx79/c5v6; 4822 130 80954). |