Philips Repair Tips
Search: philips
Results: 14210
Results: 14210
| Make | Model | Symptom | Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS |
20CT4626/05T
|
Cracking & banging. | Drys on loptx. | ||
| PHILIPS |
17PT165B AA5AB
|
Dead after lightning strike | Replace 1571 (630ma wickman) and retune stations (tuning memory had been wiped out). | ||
| PHILIPS |
17PT161A
|
To adj tuning | Dedicated r/c reqd pt no 4822 218 21249 & must press both diamond keys together to enter tuning mode | ||
| PHILIPS |
17HT5403
|
To adj sound level of this "hotel" tv | Press set up then "m" then scroll down options to vol - adj vol then press "m" | ||
| PHILIPS |
17CE1358/05B
|
Not cabbage | Tda2541 faulty - (pin 26 tda3561a = 2.2v not 10v as marked on cct) | ||
| PHILIPS |
14VP274/05
|
Sound ok no picture | If no heaters replace r3532/3537 at rear of tv pcb both 4r7 fusible | ||
| PHILIPS |
14VP184
|
Dead, blowing fuse | Replace posistor | ||
| PHILIPS |
14VP163
|
White raster with flyback lines then standby | Replace r3592 | ||
| PHILIPS |
14TX3504 TX3
|
Frame collapse. | R423 ( 33k ) o/c. | ||
| PHILIPS |
14TVCR240/05
|
Tripping due to high ht | D6335 s/c ug06b (in4148 does) & r3343 5r6 o/c in feedback reg cct | ||
| PHILIPS |
14TVCR240
|
Tripping - ht rises to 170v (should be 110v) | R3343 5r6 safety res o/c pt no 4822 052 10568, d6335 s/c pt no 4822 130 8330 | ||
| PHILIPS |
14TVCR240
|
Start up problems after replacing ts7352 | When ts7352 is replaced, it can happen that the set doesn't start up properly. there are 2 possible solutions for this problem: - use sgs type mtp3055e (4822 130 63726). - in case of a motorola type mtp3055v (4822 130 60838), add a 22 uh coil soldered i | ||
| PHILIPS |
14TVCR240
|
Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front led starts blinking, but the set doesn't start. solution: check the primary voltage (ubat) and adjust this for 14" sets to exactly 101.5 volt. (see chapter 3.1.1 of | ||
| PHILIPS |
14TVCR240
|
Spare part information | A repair kit , containing pulley shaft + worm shaft (pos. 47+48) is delivered with codenumber 4822 310 10657. this kit can be used for all turbo- and eco mechanisms ! | ||
| PHILIPS |
14TVCR240
|
Spare part information | Concerns sets produced from week 9608 until 9647. motor holder with reverse prism included: in sets produced before week 9647 the reverse prism is a fixed part of the chassis and not available as a spare part. from week 9647 onwards a motor holder (pos. | ||
| PHILIPS |
14TVCR240
|
Spare part info | As a service spare part, the picture tube will be changed back to a philips model. its code is: 4822 131 20623. if your set was previously equiped with an orion picture-tube, please make additionally the following modifications when mounting this philips | ||
| PHILIPS |
14TVCR240
|
Set produces audible noise in stand-by | Add a small lebl (leading edge blanking) pcb, to avoid auto oscillation of transformer 5330 (or 5331). a modification letter is included with the lable pcb. this pcb is available with service nr. 4822 214 12173. since production week 9723 this circuit is | ||
| PHILIPS |
14TVCR240
|
Set produces audible noise in stand-by | Add a small lebl (leading edge blanking) pcb, to avoid auto oscillation of transformer 5330 (or 5331). a modification letter is included with the lebl pcb. this pcb is available with service nr. 4822 214 12173. | ||
| PHILIPS |
14TVCR240
|
Service manual information | Deviations between 14tvcr240/01 and 14tvcr240/01n: for 14tvcr240/01n, use the service manual of 14pv162/01. additional codenumbers: position description codenumber 1 frame assy 4822 464 51055 1/5 lift | ||
| PHILIPS |
14TVCR240
|
Service hint | On certain tvcr sets sent to the eastern european countries, the vps function cannot be activated via the remote control. inside the remote control, a jumper is connected to pin 10 of the ic instead of being connected to pin 11: - when the jumper is on p |