Samsung Repair Tips

Search: samsung
Results: 3802

Make	Model	Symptom	Problem	Solution	By
SAMSUNG	CL21Z43MG KSCA. AA41	Echoing the sides when the brightness of the image was strong	D804 and d805 in primary power supply	Just replace and run for the hug	Bynhoteck
SAMSUNG	LE32A559 BN44-00208A	After turning it off, it will not turn back on unless it is removed from the power supply.	Check RP809, RP810, RP811, RP812, RP816 and optocoupler.		Mantunes
SAMSUNG	CL-21M6MQ	LED is on, when you turn it on, when you press power, the LED turns off +b and resets and the TV does not turn on	The resistor, r831 of 123k changed to any value. just change		CST ELETRONICA SERROTA SENADOR SA
SAMSUNG	29K40MQ	I'm sound	R606 51k open	R606	This email address is being protected from spambots. You need JavaScript enabled to view it.
SAMSUNG	PL51E450A1G	It doesn't turn on, the screen flashes and no image.	Chap. ceramic na main plate ref. c226 com escape.		CARLOS-KBE
SAMSUNG	LN37B530P2M	Dark fabric sem contrast image type negative	Tcom board defect	Replace ci smd as15f of tcom board	EDUARDO TV AV
SAMSUNG	PL51D491	Turns on normally, tsound is no image and sound. The auto gen was done and passed.	Check voltage on regulators >>> ic204>1.10v, ic203>2.5v, ic201>3.26v, ic1204>3.20v, ic202>3.20v, ic2011>1.2v, ic 205>1.5v.	In my case it was the ic204 getting hot and the voltage rising. I replaced it with a z1073. the 2011 ic also has this defect
SAMSUNG	PL43D491A4G		No image, normal alloy, was made auto gen. On the control board, place a jumper on pins 3 and 4, turn off the main cable and turn on the TV. image has to appear.	The test was done and the image appeared, check the voltage on IC204>1.10V, IC203>2.5V, IC201>3.26V, IC1204>3.20V, IC202>3.20V, IC2011>1.2V, IC 205>1.5V. in my case it was the ic204 getting hot and the voltage rising. I replaced it with a z1073.
SAMSUNG	UN40ES6100GXDZ	Cannot find wifi network or does not connect wifi	Due to new protocols, some routers or operators are no longer compatible for br	Access service mode (mute+182+power on) "control" option --> "sub option" option --> "wifi region" option --> replace the "wifi region" to "a" or "b"	Snegs Eletrônica
SAMSUNG	UN40C5000	Turns on, but no image comes out. backlight comes on.	Defective tcon. ict2 reg 3v3 reset. to replace.		Joaomvjr
SAMSUNG	T22A300	Blinking LED does not turn on	Diode dm887		Damião
SAMSUNG	LN32B530	No image, normal sound	Lamps off.	General resoldering of the power supply.	Eletrônica sul minas e cel
SAMSUNG	CL21Z43MQ	When turned on, the image appears normal, then it heats up and the image becomes deformed or serrated	Ey134= capacitor poliester 274j/400v=n27/400v	Replaced and solved the problem, the image was perfect (obs. in my case I didn't have the 274j, I replaced it with a 304j)	Antonio Carlos (Eletrônica Renascer)Boa Vista do Gurupi-MA
SAMSUNG	LN40D550	Tripled image, embarrassed	Durex was placed on 1 of the flats, covering around 30% of a flat		Invision Assistencia
SAMSUNG	UN48H6800AGXZD	No image	1. observe how many LEDs are on on the t-con. tsound are 3 LEDs that must be lit.<br>2.if only one LED lights up, disconnect the t-con cable that comes from the power supply.<br>3.turn it off and plug it into the socket and note that 2 will light up LEDs and, simultaneously, the image LEDs.	Replace the smd capacitor in the image in this thread or the nearby capacitors dica un48h6800agxzd.	antonio copiadoras
SAMSUNG	UN32FH4205G	Dead	Tsound is no secondary power supply	Dm807c shorted to the power supply and just replace it	Elias tv Natal R\|N
SAMSUNG	PL43F4000	Restarting randomly	Resolve/replace do c1024 smd pci main		Angelo MG
SAMSUNG	CL-21Z50MQ	Working but no image, enlarge the screen nothing happens	10k r270, open, is close to the processor		Dj Velk
SAMSUNG	CL-21Z50MQ	Sound noise, hissing, in av mode	C214 leak or short		Dj Velk
SAMSUNG	CL-21Z50MQ	Hissing sound interference in av mode	C214 leak or short	Remove or replace	Dj Velk