Sharp Repair Tips

Search: sharp
Results: 1789

Make	Model	Symptom	Problem	Solution	By
SHARP	2017	Closed horizontal	C 617 ( 560 p / 250v )		JOHN
SHARP	1453	Dead	Trafo drive	Replaced the same TV that worked normally	filipak
SHARP	C2082	Does not fully open the vertical strip on both sides of 10 cm at the bottom and top	Change c 507 1000 / 35 volts weak.		jaironuness
SHARP	C-2053	Vertical stretched	Ic104 aberto (diodo zener 33v)	Replace ic104	ric
SHARP	C20R11	Turns on after a few seconds turns off	Unbelievable 33v zener shorted killing the 115v plus b line	Replace do zener 33v (ic 1005)	VAGNER NARDES
SHARP	C1467 B	It turns on sometimes, always after it is hot, with all voltages at the power supply	Bu2508dx with leakage (replace without measuring) and c616 with leakage (6n8/1600v)		vagnernardes
SHARP	1453	Tune in all channels except 4	It was memory. I removed the blessed one, turned on the TV and then put it back and bingo the blessed one came back 4 hugs to everyone		Talmid
SHARP	C- 2038	Doesn't turn on (power supply keeps trying to start)	C607 with leak	Capacitor replaced	Ivan
SHARP	C-1692B	Horizontal line, in the center of the screen.	If not s.vert, subst. tda8305a pin 3 voltage-free drive.		LUIR FRANK
TV SHARP	C2038	There is no image	Without power supply	Capacitor c621 shorted	josuel barreto
SHARP	1440B	After a few seconds the TV turns off by itself, when you lower the screen it looks fine.	Open contrast trimpot (100k).		luciano fontes de souza
SHARP	20R12	Turns off by itself	I removed the 658 diode		marcos
SHARP	C-2OR12	Turning off when. puts the'antenna signal when. There is no signal, the TV won't turn off	Turn off 0 d-658 near the flay back		This email address is being protected from spambots. You need JavaScript enabled to view it.
SHARP	C20R12	Retraction, no picture normal sound	Lack of y(luminance) us draiv rgb	Open resistor r 824	DEBIQUE
SHARP	37EM33S CA-1	Locked no child lock	You must enter service mode (with TV off on power, press vol- and ch+ on TV and turn on power). select > nvm > 4d > password on > enter w/ r/c (0) to unlock; exit to menu on the ground floor.		jose luis calcada
SHARP	TVC20R12 / 20RS02/03 20S02	Without contrast and protection acting	R675 of 5k6 connected to pin 10 of the open flay back	R675 replacement	This email address is being protected from spambots. You need JavaScript enabled to view it.
SHARP	27HS60	Horizontal exit burn	Ci do vertical short		laurindo
SHARP	20R12	The TV turns on normally, but the tube filament does not light up.	I measured the voltage coming out of the flay backq and it was approximately 4 to 5 volts and this voltage came out of pin 8 of the flay back. If it is coming out, check the tube socket to see if it is coming. In my case the cable was broken and that's why I struggled a little but I discovered the defect lol		This email address is being protected from spambots. You need JavaScript enabled to view it.
SHARP	C2999	Sem osd	Change q2001 with leak		Reginaldo
SHARP	20R11	Turning off after a certain time	Abl circuit	Verificar r432, r664	Lecram