☰

Sony Repair Tips




AIWA
BEKO
CCE
CINERAL
DAEWOO
FUNAI
GRADIENTE
GRUNDIG
HITACHI
ITT
JVC
LG
MITSUBISHI
PANASONIC
PHILCO
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SHARP
SONY
THOMSON
TOSHIBA
VESTEL


Search: sony
Results: 20100
Make Model Symptom Problem Solution By
SONY SONY WEGA
picture with black bars even in content 4: 3 Broken deflector replace the deflector for another Evandro
SONY KDL-32R305B
Camo appeared soon restart 3 times and then flashing red LED when I put finger over the Ci Drive Led made a xiado I replaced the same for another of scrap and resolved IC9001 Ci drive BD-9397EFV Jr informática
SONY MHC GTX888
Apparatus connected and appeared eject on the display and shut down Tape mechanism with problem repair or locking the mechanism down.
SONY KDL-55W805C
Turn on, light Stanby to Power, no flash, don't write Sony right away and in seconds flashes error 06. After analysis I concluded the LED inverter plate defect, when removing shielding from the I.C Drive I.C of the LEDs and the TV again I.C RESSOLDA LED Drive on Inverter Plate. MIGUELTV
SONY KDL-46EX605
Threatens to light the backlight and then LED flashes 6x. power supply that feeds backlight with low voltage. PS6800 fuse open. It is at the bottom near the LED connectors. Persio (TVCompany)
SONY KDL-42W655A
Turn on and enter protection, turning off and flashing 6x red LED. First to do is check the LED bus. In my case all LEDs were ok. Unique way of making it no protection was putting a 1mega resistor between Pins 3 and 37 of CI BD9422, monitoring the voltage in pin 3 needs to have around 1.5V so as not to protect ZW ELETRONICA
SONY KDL-46R475A
TPV-AOC 		Turn on, after a few minutes the TV erases the LEDs and is just the sound, no mistake LED bar is the same LED bar of 46pfl4508/5500/3508/4908 replace LED bar, import from aliexpress: external link ... MIGUELTV
SONY XBR-55X855G
Does not work remote control Oxidation and underground trail on the receiving plate on TV Redo the trail Nialad
SONY 40EX715
The power supply relay is hitting nonstop and TV doesn't turn on. Diode D6303 along with the defective relay. Put a 12V Zener diode or a 1N4007 good. Alessandro Barcelos -STA MARIA
SONY ADP-160CR AAB
It has standby but when it tries to connect 5V drops slowly until it zero IC41 with defective IC41 replace
SONY KDL-40EX405 32EX405 40BX405....
connects the green LED and nothing else, present power supplys.inverter is fed but not triggered Short in the processor bus SMD 0805 capacitor between the processor and the AV connector Davi.sls
SONY KD-49X705F
Flash 4 times flashing 4 times ch. t con in the short CPC.1105 left side, fuse inter plate F.1000 5A Solved eletronica fama
SONY HCD-ZUX9
Without sound on the 4 outputs C341 Capacitor in Pin 74 of IC 200 Audio Processor shortly killing 4.5V Capacitor replace C341 Eletronica Moura
SONY WEGA KV29FA210
BA5D 		Turns off after 6 to 10 minutes D113 Open Resolved Eduardo
SONY MHC-990
GN990 		Call and turn off then. Initially I removed the STK412-170 but did not set the reme. Gilmar Roberto Alves
SONY MHC-GTR888
Does not call, without 7.6V on the power supply exit! But it appears when it takes off the outlet PC704 Coupler Photo Rodrigo cofferi
SONY KDL-40R355B
Download leds Put 15k resistor between GND and pin 35 of the tense led drive drops to 29.4V Techmix eletrônica
SONY KDL-40NX715
Alloy with normal picture, it works for about 10 minutes then shuts down and flashing Sty 6x The defect is relatively simple, the difficult is to fix. Defect: 3 burnt or short LEDs, but you can't find the LED bars anywsound to sell Trying to replace the burnt LEDs from the LED bar, in my case it didn't work out because it ended up breaking the LED bar trail that is very thin PEDRO IGOR
SONY KDL-50W655
turn on and off IC9301 regulator heating too much, I replaced and worked normally without heating Mirage Eletrônica
SONY MHC-V5
triggering protection 3 Clean and wash the plates and remove the Q1007 transistor from the amplifier plate Mirage Eletrônica